Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 524
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-27
48.Remove the brake plates (five pieces), brake discs (six
pieces) and pressure plate.
49.Remove the wave spring.
50.Remove the parking pawl shaft, and then remove the
spacer and spring.
51.Remove the two parking roller support shafts, and then
remove the parking roller support.
52.Remove the one-way clutch inner race and low-reverse
brake piston as follows:
(1) Using special tools MD998903 <F4A42> or MD998338
<F4A51> and MD998924, compress the one-way clutch
inner race.
NOTE: This illustration shows F4A51.
(2) Remove the snap ring.
(3) Remove the special tools.
(4) Remove the one-way clutch inner race, O-ring, spring
retainer, return spring and low-reverse brake piston.
AKX01022
AKX01023
AKX01033
AKX01034
AKX01107AB
MD998924
MD998903
<F4A42> OR
MD998338
<F4A51>
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-28
53.Remove the four <F4A51> or three <F4A42> transfer drive
gear bearing mounting bolts.
Then, turn the gear 1/8 turn (45 degree angle) and remove
the remaining bolts.
F4A42 = seven mounting bolts
F4A51 = eight mounting bolts
54.Remove the transfer drive gear.
55.Remove the cap.
56.Using a chisel, remove the staked nut from the output shaft.
AKX01035
<F4A42>
AB
AKX01110
AKX01036
AKX01082
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-29
CAUTION
The jam nut is reverse threaded.
57.Use special tools MB991625 and MB990607 to remove the
output shaft jam nut.
58.Remove the bearing retainer mounting bolt.
59.Tap on the rear end of the output shaft to remove the output
shaft, taper roller bearing and collar.
60.Remove the outer race and the spacer.
61.Remove the snap ring.
AKX01037
MB990607
AB
MB991625
AKX01038
AKX01039
AKX01040
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-30
ASSEMBLY
CAUTION
•
Do not reuse the gasket, O-ring, oil seal. Always
replace with a new one when assembling.
•
Do not use grease other than petroleum jelly (Vaseline).
•
Apply ATF to friction components, rotating parts, and
sliding parts before installation. Immerse a new clutch
disc or brake disc in ATF for at least two hours before
assembling them.
•
When replacing a bushing, replace the assembly which
it belongs to.
•
Do not use cloth gloves or shop towels during
assembly. Use nylon cloth or other lint-free material.
1. Install special tool MD998412 in the installation screw hole
of the transfer drive gear bearing located in the transaxle
case. Using this as a guide, install the transfer drive gear
bearing and gear in the transaxle case.
2. Tighten the seven mounting bolts (F4A42) and eight
mounting bolts (F4A51) of the transfer drive gear bearing to
the specified torque.
Tightening torque: 34
±
2 N
⋅
m (25
±
1 ft-lb)
AKX01088AB
MD998412
AKX01035
<F4A42>
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст