Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 14
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-53
CAUTION
Do not overfill the reserve tank.
12.Add coolant to the reserve tank between the "FULL" and
"LOW" mark if necessary.
15. DISC BRAKE PADS (INSPECT FOR WEAR)
M1001003200097
Check for fluid contamination and wear. Replace the complete
set of pads if defective.
Thickness of lining
Minimum limit: 2.0 mm (0.08 inch)
CAUTION
The pads for the right and left wheels should be replaced
at the same time. Never split or intermix brake pad sets. All
four pads must be replaced as a complete set.
16. REAR DRUM BRAKE LININGS AND REAR
WHEEL CYLINDERS (INSPECT FOR WEAR AND
LEAKS)
M1001003300083
1. Remove the brake drum and check the thickness of brake
shoe lining for wear. Check the automatic brake adjusting
system by hand to see if it operates smoothly. Also see if the
gears are in proper mesh with each other. To assure smooth
operation, apply a very thin coat of multipurpose grease to
the friction surface of the adjuster and link shaft.
CAUTION
The shoes for the right and left wheels should be replaced
at the same time. Never split or intermix brake shoe seats.
All four shoes must be replaced as a complete set.
2. Inspect the wheel cylinder boot for evidence of a brake fluid
leak. Visually check the boot for cuts, tears or heat cracks.
(A slight amount of fluid on the boot may not be a leak, but
may be preservative fluid used at assembly.) Check the
Brake Shoes for Wear.
Thickness of lining
Minimum limit: 1.0 mm (0.04 inch)
ACX00898 AB
AC002717AB
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-54
17. BRAKE HOSES (CHECK FOR
DETERIORATION OR LEAKS)
M1001003400091
Inspection of brake hoses and tubing should be included in all
brake service operations.
The hoses should be checked for:
1. Correct length, severe surface cracking, pulling, scuffing or
worn spots. (If the fabric casing of the hoses is exposed by
cracks or abrasion in the rubber hose cover, the hoses
should be replaced. Eventual deterioration of the hose and
possible bursting failure may occur.)
2. Incorrect installation, casing twisting or interference with
wheel, tire or chassis.
18. BALL JOINT AND STEERING LINKAGE
SEALS (INSPECT FOR GREASE LEAKS AND
DAMAGE)
M1001003500098
1. These components, which are permanently lubricated at the
factory, do not require periodic lubrication. Damaged seals
and boots should be replaced to prevent leakage or
contamination of the grease.
2. Inspect the dust cover and boots for proper sealing, leakage
and damage, and replace them if defective.
19. DRIVE SHAFT BOOTS (INSPECT FOR
GREASE LEAKS AND DAMAGE)
M1001003600095
1. These components, which are permanently lubricated at the
factory, do not require periodic lubrication. Damaged seals
and boots should be replaced to prevent leakage or
contamination of the grease.
2. Inspect the dust cover and boots for proper sealing, leakage
and damage, and replace them if defective.
AC000107AB
BRAKE
TUBE
BRAKE
HOSE
AC000108
BOOT
DUST
COVER
AB
AC000109 AB
BOOTS
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-55
20. SRS AIR BAG (INSPECT FOR SRS SYSTEM)
M1001003700092
The SRS must be inspected by an authorized dealer 10 years
after the car manufacture date shown on the certification label
located on the left center sill.
SRS Warning Light Check
Turn the ignition key to the "ON" position. Does the "SRS"
warning light illuminate for about seven seconds, and then
remain off for at least five seconds after turning OFF? If yes,
the SRS system is functioning properly. If no, refer to GROUP
52B, Diagnosis
.
AC000111
DATE OF
MANUFACTURE
CERTIFICATION LABEL
AB
AC000112 AB
SRS WARNING LIGHT
MAINTENANCE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-56
SRS Component Visual Check
DANGER
Wait at least 60 seconds after disconnecting the
battery cable before doing any further work. The SRS
system is designed to retain enough voltage to
deploy the air bag for a short time even after the
battery has been disconnected, so serious injury may
result from unintended air bag deployment if work is
done on the SRS system immediately after the battery
cable is disconnected.
WARNING
Battery posts, terminals and related accessories
contain lead and lead compounds. WASH HANDS
AFTER HANDLING.
1. Turn the ignition switch to the "LOCK" (OFF) position,
disconnect the negative battery cable and tape the terminal.
2. Remove the floor console assembly. (Refer to GROUP 52A,
Floor Console
3. Disconnect a connector from the SRS-ECU.
Side Impact Sensors
WARNING
•
If the side impact sensor is not installed securely
and correctly, the side air bag may not operate
normally.
•
If a dent, crack, deformation or rust is detected,
replace with a new sensor.
1. Check the side impact sensor and bracket for dents, cracks
or deformation.
2. Check the connector for damage, and terminal for
deformation.
3. Check that there is no bending or corrosion in the side outer
panel (ECLIPSE) or quarter panel (ECLIPSE SPYDER).
ACX00902 AB
TAPE
BATTERY
BATTERY CABLE
AC000113
REAR
SPEAKER
(LH)
SIDE IMPACT
SENSOR
FRONT OF
VEHICLE
AC
< ECLIPSE >
AC002718AB
FRONT
VEHICLE
SIDE IMPACT
SENSOR
REAR
SPEAKER(LH)
<ECLIPSE SPYDER>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст