Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 659
MARK
TSB Revision
EXTERIOR
51-23
M A R K
SPECIAL TOOL
M1511000600315
REMOVAL AND INSTALLATION
M1511011800067
Required Special Tool:
•
MB990528: Stripe Tape Spatula
INSTALLATION SERVICE POINT
>>A<< MARK INSTALLATION
1. APPLICATION LOCATION
The distance A (from the mark right end to the notch) should
be identical to the distance A' (from the front door opening
line to the mark right end).
TOOL
TOOL NUMBER AND
NAME
REPLACED BY MILLER
TOOL NUMBER
APPLICATION
MB990528 Stripe tape
spatula
Bonding of the mark
MB990528
AC003660
< ECLIPSE >
< ECLIPSE SPYDER >
AB
1
2
3
1
4
1
2
3
1
1. TOP MARK
>>A<<
2. ENGINE SPECIFICATION MARK
>>A<<
3. GRADE MARK (GT, RS, GS)
>>A<<
4. SPYDER MARK
MARK
TSB Revision
EXTERIOR
51-24
CAUTION
•
Work in a dust-free workplace with temperature of 20 -
38
°
C
(60 - 100
°
F).
•
If workplace temperature is under 20
°
C
(60
°
F), warm
tape and vehicle body (adhesion area) to 20 - 38
°
C
(60 -
100
°
F).
2. Install the tape by the following procedure.
(1) Use 3M
AAD Part number 8906 or equivalent to wipe
off oil from stripe tape adhesion area.
(2) Remove protective paper from back of stripe tape and
adhere entirely to indicated area.
AC003661
FRONT FENDER PANEL
PRESS LINE
A
A'
FRONT DOOR
OPENING LINE
ALIGN THE MARK BOTTOM END
WITH THE LIFTGATE BOTTOM END.
ALIGN THE MARK NOTCH WITH
THE LIFTGATE RIGHT END.
ALIGN THE MARK BOTTOM END WITH
THE TRUNK LID BOTTOM END.
TRUNK LID END LINE
ALIGN THE MARK LINE END WITH
THE TRUNK LID LIFT END.
AB
SPYDER MARK
GRADE MARK
GT (also applicable for GS)
ENGINE SPECIFICATION MARK
LH SIDE
NOTE
RH side is symmetrical on LH side.
MARK
TSB Revision
EXTERIOR
51-25
CAUTION
•
Pressing the mark horizontally may lead to a slack,
clinching or improper position.
•
If the mark is pressed improperly, the mark may be
easily peeled off.
(3) Make sure that air bubbles are not trapped in the
application surface. When applying the mark, use special
tool MB990528 to press the mark from its center to top
and bottom gradually.
(4) Peel off an application tape (top protection paper)
horizontally and carefully from one end. If an air bubble is
left in the mark, open a hole by using a needle, and then
use special tool MB990528 to expel the air bubble.
AC000548 AB
30 - 45˚
MB990528
APPLICATION TAPE
AC000549
CORRECT INCORRECT
AB
APPLICATION TAPE
DOOR MIRROR
TSB Revision
EXTERIOR
51-26
D O O R M IR R O R
SPECIAL TOOL
M1511000600326
REMOVAL AND INSTALLATION
M1511006400063
TOOL
TOOL NUMBER AND
NAME
REPLACED BY MILLER
TOOL NUMBER
APPLICATION
MB990784
Ornament remover
General service tool
Removal of remote con-
trolled mirror switch
MB990784
AC003328
8
7
6
5
3
View A
View A
2
4
6
8
1
B
B
A
A
CLAW
SECTION A – A
6
2,3
2,3
6
SECTION B – B
View A
2,3
(ELECTRIC)
(DIRECT)
AB
NOTE
: Claw position
1.
REMOTE CONTROLLED MIRROR
SWITCH
DOOR MIRROR REMOVAL STEPS
•
DOOR TRIM (REFER TO GROUP42
.)
2. DELTA COVER, INNER
3. TWEETER COVER
4. PAD
5. TWEETER
6. DELTA COVER BASE
7. HARNESS CONNECTOR
<VEHICLES WITH REMOTE
CONTROLLED MIRROR>
8. DOOR MIRROR ASSEMBLY
DOOR MIRROR REMOVAL STEPS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст