Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 550
TRANSAXLE (TRANSMISSION) MOUNTING
TSB Revision
POWER PLANT MOUNT
32-7
TR AN SAXLE (TRA NSM ISSIO N ) M O U N TIN G
REMOVAL AND INSTALLATION
M1321001400098
CAUTION
Mounting locations marked by
*
should be provisionally tightened, and then fully tightened after
placing the vehicle horizontally and loading the full weight of the engine on the vehicle body.
Required Special Tools:
•
MB991453: Engine Hanger
•
MZ203827: Engine Lifter
Pre-removal and Post-installation Operation
•
Air Cleaner Assembly Removal and Installation (Refer to
GROUP 15, Air Cleaner
•
Battery and Battery Tray Removal and Installation (Refer
to GROUP 54A, Battery
•
Centermember Removal and Installation (Refer to
•
Transaxle and Rear Roll Stopper Connecting Bolt
Removal and Installation (Refer to
•
Rear Roll Stopper Bracket Removal and Installation <2.4L
Engine-M/T> (Refer to GROUP 22B, Transaxle
.),
<2.4L Engine-A/T> (Refer to GROUP 23B, Transaxle
.)
AC000301 AB
1
2
81 ± 12 N·m*
60 ± 9 ft-lb*
57 ± 7 N·m
42 ± 5 ft-lb
N
REMOVAL STEPS
<<A>>
1.
TRANSAXLE MOUNT BRACKET
>>A<<
2.
TRANSAXLE MOUNT STOPPER
TRANSAXLE (TRANSMISSION) MOUNTING
TSB Revision
POWER PLANT MOUNT
32-8
REMOVAL SERVICE POINT
<<A>> TRANSAXLE MOUNT BRACKET REMOVAL
1. Install special tools MB991453 and MZ203827 to the vehicle
body to support the engine and transaxle assembly.
2. Remove the centermember and rear roll stopper bracket.
3. Remove the bolt and nut of the transaxle mount bracket.
4. After lowering the engine and transaxle assembly, remove
the transaxle mount bracket.
INSTALLATION SERVICE POINT
>>A<< TRANSAXLE MOUNT STOPPER INSTALLATION
Clamp the transaxle mount stopper so that the arrow points in
the direction as shown in the diagram.
ACX00406
MZ203827
AB
MB991453
AC000302
ENGINE SIDE
ARROW
TRANSAXLE
MOUNT
BRACKET
AB
TRANS-
AXLE
MOUNT
STOPPER
ENGINE ROLL STOPPER AND CENTERMEMBER
TSB Revision
POWER PLANT MOUNT
32-9
EN G INE R O LL STO PPER A N D C ENTER M EM BER
REMOVAL AND INSTALLATION
M1321002300050
CAUTION
Mounting locations marked by
*
should be provisionally tightened, and then fully tightened after
placing the vehicle horizontally and loading the full weight of the engine on the vehicle body.
AC000303
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 10 N·m*
34 ± 7 ft-lb*
74 ± 4 N·m
55 ± 3 ft-lb
74 ± 4 N·m
55 ± 3 ft-lb
93 ± 15 N·m
69 ± 11 ft-lb
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 5 N·m*
34 ± 3 ft-lb*
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 10 N·m*
34 ± 7 ft-lb*
93 ± 15 N·m
69 ± 11 ft-lb
74 ± 4 N·m
55 ± 3 ft-lb
45 ± 5 N·m*
34 ± 3 ft-lb*
<3.0L ENGINE>
<2.4L ENGINE>
1
2
2
3
4
5
6
7
8
3
9
10
10
9
1
5
4
8
7
6
3
2
2
2
N
N
AB
ENGINE ROLL STOPPER AND CENTERMEMBER
TSB Revision
POWER PLANT MOUNT
32-10
INSTALLATION SERVICE POINT
>>A<< FRONT ROLL STOPPER INSTALLATION
Install so that the hole in the front roll stopper is facing towards
the front of the vehicle.
FRONT ROLL STOPPER,
CENTERMEMBER REMOVAL
STEPS
1.
TRANSAXLE AND FRONT ROLL
STOPPER CONNECTING BOLT
2.
CENTERMEMBER MOUNTING
BOLTS
3.
STOPPER
4.
CENTERMEMBER
>>A<<
5.
FRONT ROLL STOPPER
6.
COLLAR
7.
BUSHING (LOWER)
8.
BUSHING (UPPER)
REAR ROLL STOPPER
REMOVAL STEPS
9.
TRANSAXLE AND REAR ROLL
STOPPER CONNECTING BOLT
10. REAR ROLL STOPPER
FRONT ROLL STOPPER,
CENTERMEMBER REMOVAL
STEPS (Continued)
AC000304 AB
FRONT OF VEHICLE
HOLE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст