Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 463
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-144
STEP 12. Check connectors C-61 <2.4L Engine> or C-63
<3.0L Engine> at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 13. Check the Park/Neutral position switch.
Check for continuity between terminals for each selector
position.
NOTE: For vehicles with sport mode, four positions (P, R, N, D)
are used.
Q: Is the switch operating properly?
YES : Go to Step 14.
NO : Replace the Park/Neutral position switch. Refer to
GROUP 23B, Transaxle
.
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
ITEMS
TERMINAL
CONNECTION OF
TESTER
SPECIFIED
CONDITION
P
3
−
8, 9
−
10
Less than 2 ohm.
R
7
−
8
N
4
−
8, 9
−
10
D
1
−
8
3
5
−
8
2
2
−
8
L
6
−
8
AC004672
DIPSTICK
PARK/NEUTRAL
POSITION (PNP)
SWITCH
AC
AC001846
P
R
N
D
3
2
L
AB
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-145
STEP 14. Check connector B-41 at the Park/Neutral
position switch for damage.
Q: Is the connector in good condition?
YES : Go to Step 15.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 15. Check the switch output voltage at PCM
connector C-61 <2.4L Engine> or C-63 <3.0L Engine> by
backprobing.
(1) Do not disconnect connector C-61 <2.4L Engine> or C-63
<3.0L Engine>.
(2) Turn the ignition switch to "ON" position.
(3) Move the selector lever to "R" position.
(4) Measure the voltage between terminal 108 and ground by
backprobing.
•
Voltage should be battery positive voltage.
(5) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 12.
NO : Go to Step 16.
STEP 16. Check connectors C-61 <2.4L Engine> or C-63
<3.0L Engine> at PCM for damage.
Q: Is the connectors in good condition?
YES : Go to Step 17 <Vehicles with sports mode>. Repair it
because of the harness open circuit or short circuit to
ground between Park/Neutral position switch
connector B-41 terminal 7 and PCM connector C-61
<2.4L Engine> or C-63 <3.0L Engine> terminal 108.
<Vehicles without sports mode>
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC001844
CONNECTOR: B-41
DIPSTICK
AB
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
AC001904
C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
CONNECTOR HARNESS
SIDE VIEW
AD
AC001657
CONNECTOR: C-61 <2.4L ENGINE> OR
C-63 <3.0L ENGINE>
PCM
AN
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-146
STEP 17. Check harness for open circuit or short circuit to
ground between Park/Neutral position switch connector B-
41 terminal 7 and PCM connector C-63 <Vehicles with
sport mode> terminal 108.
Q: Is the harness wire in good condition?
YES : Go to Step 18.
NO : Repair it.
STEP 18. Check connectors C-27 at intermediate
connector C-43 at combination meter for damage
<Vehicles with sport mode>.
Q: Are the connectors in good condition?
YES : Go to Step 19.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC001844
CONNECTOR: B-41
DIPSTICK
AB
AC001657
CONNECTOR: C-63
PCM
AO
AC001741
CONNECTOR: C-27
AK
AC001729 AO
CONNECTOR: C-43
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-147
STEP 19. Check harness for short circuit to ground
between Park/Neutral position switch connector B-41
terminal 7 and combination meter connector C-43 terminal
10 <Vehicles with sport mode>.
Q: Is the harness wire in good condition?
YES : Repair it because of the connector and the harness
short circuit to ground between output signal line of
Park/Neutral position switch connector B-41 terminal
7.
NO : Repair it.
AC001844
CONNECTOR: B-41
DIPSTICK
AB
AC001729 AO
CONNECTOR: C-43
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст