Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 556
STABILIZER BAR
TSB Revision
FRONT SUSPENSION
33A-17
STA B ILIZER B A R
REMOVAL AND INSTALLATION
M1332004000059
Required Special Tool:
•
MB990326: Preload Wrench
REMOVAL SERVICE POINT
<<A>> STABILIZER BAR REMOVAL <3.0L ENGINE>
Turn the steering wheel to the right to remove the left end of the
stabilizer bar.
Pre-removal Operation
•
Front Exhaust Pipe Removal <2.4L ENGINE> (Refer to
GROUP 15, Exhaust Pipe and Main Muffler
.)
•
Centermember Removal <2.4L ENGINE> (Refer to
GROUP 32, Engine Roll Stopper, Centermember
•
Stay Removal <2.4L ENGINE> (Refer to GROUP 32,
Crossmember
•
Lower Arm Removal (Refer to
Post-installation Operation
•
Check the Dust Cover for Cracks or Damage by Pushing
it with Your Finger.
•
Lower Arm Installation (Refer to
•
Stay Installation <2.4L ENGINE> (Refer to GROUP 32,
Crossmember
•
Centermember Installation <2.4L ENGINE> (Refer to
GROUP 32, Engine Roll Stopper, Centermember
•
Front Exhaust Pipe Installation <2.4L ENGINE> (Refer to
GROUP 15, Exhaust Pipe and Main Muffler
.)
AC003543AC
44 ± 10 N·m
33 ± 7 ft-lb
1
4
3
2
3
2
<2.4L ENGINE>
<3.0L ENGINE>
44 ± 10 N·m
33 ± 7 ft-lb
44 ± 10 N·m
33 ± 7 ft-lb
REMOVAL STEPS
1.
STABILIZER LINK
>>A<<
2.
STABILIZER BRACKET
>>A<<
3.
BUSHING
<<A>>
>>A<<
4.
STABILIZER BAR
STABILIZER BAR
TSB Revision
FRONT SUSPENSION
33A-18
INSTALLATION SERVICE POINT
>>A<< STABILIZER BAR/BUSHING/STABILIZER BAR
BRACKET INSTALLATION
Position the stabilizer bar so that the left side identification
mark is at the shown position, and tighten the stabilizer bar
bracket mounting bolt.
INSPECTION
M1332002000064
•
Check the bushing for wear and deterioration.
•
Check the stabilizer bar for deterioration or damage.
•
Check all bolts for condition and straightness.
STABILIZER LINK BALL JOINT BREAKAWAY TORQUE
CHECK
1. After shaking the ball joint stud several times, install the nut
to the stud and use special tool MB990326 to measure the
breakaway torque of the ball joint.
Standard value: 3.4
−
9.0 N
⋅
m (30
−
80 in-lb)
2. If the measured value exceeds the standard value, replace
the stabilizer link.
3. If the measured value is lower than the standard value,
verify that the ball joint turns smoothly without excessive
play. If so, the ball joint is reusable.
STABILIZER LINK BALL JOINT DUST COVER CHECK
1. Check the dust cover for cracks or damage by pushing it
with your finger.
2. If the dust cover is cracked or damaged, replace the
stabilizer link.
AC001128 AB
APPROXIMATELY 10 mm (0.4 in)
INSIDE OF
THE BODY
AC001129
MB990326
AB
SPECIFICATIONS
TSB Revision
FRONT SUSPENSION
33A-19
SPECIFIC ATIO NS
FASTENER TIGHTENING SPECIFICATIONS
M1332008500045
GENERAL SPECIFICATION
M1332000200040
COIL SPRING <ECLIPSE>
COIL SPRING <ECLIPSE SPYDER>
ITEMS
SPECIFICATIONS
Lower arm assembly
Lower arm clamp bolt
81
±
12 N
⋅
m (60
±
9 ft-lb)
Lower arm to clamp connection nut
99
±
11 N
⋅
m (73
±
8 ft-lb)
Lower arm to crossmember connection nut
108
±
10 N
⋅
m (80
±
7 ft-lb)
Lower arm to knuckle connection nut
108
±
10 N
⋅
m (80
±
7 ft-lb)
Stabilizer bar
Stabilizer bracket bolt
44
±
10 N
⋅
m (33
±
7 ft-lb)
Stabilizer link nut
44
±
10 N
⋅
m (33
±
7 ft-lb)
Strut assembly
Stabilizer link nut
44
±
10 N
⋅
m (33
±
7 ft-lb)
Strut assembly jam nut
64
±
5 N
⋅
m (47
±
4 ft-lb)
Strut assembly to body connection nut
44
±
5 N
⋅
m (33
±
3 ft-lb)
Strut assembly to knuckle connection nut
300
±
24 N
⋅
m (221
±
18 ft-lb)
ITEMS
RS, GS
−
M/T
GS
−
A/T, GT
−
M/T
GT
−
A/T
Wire diameter mm (in)
14.3 (0.56)
14.5 (0.57)
14.7 (0.58)
Average diameter mm (in)
169.0 (6.65)
169.0 (6.65)
169.0 (6.65)
Free length mm (in)
311.5 (12.26)
320.0 (12.60)
328.5 (12.93)
ITEMS
GS
GT
−
M/T
GT
−
A/T
Wire diameter mm (in)
14.7 (0.58)
15.0 (0.59)
15.2 (0.60)
Average diameter mm (in)
169.0 (6.65)
169.0 (6.65)
169.0 (6.65)
Free length mm (in)
328.5 (12.93)
336.5 (13.25)
345.0 (13.59)
SPECIFICATIONS
TSB Revision
FRONT SUSPENSION
33A-20
SERVICE SPECIFICATIONS
M1332000300047
COMPONENT IDENTIFICATION
M1331001300058
CAMBER ADJUSTING BOLT
ITEMS
SPECIFICATIONS
Toe-in mm (in)
0
±
3 (0
±
0.12)
Steering angle
<ECLIPSE>
Inner wheel
2.4L ENGINE
36
°
12'
±
2
°
00'
3.0L ENGINE
31
°
00'
±
2
°
00'
Outer wheel
(reference)
2.4L ENGINE
30
°
24'
3.0L ENGINE
27
°
00'
Steering angle
<ECLIPSE SPYDER>
Inner wheel
2.4L ENGINE
36
°
12'
±
2
°
00'
3.0L ENGINE
33
°
60'
±
2
°
00'
Outer wheel
(reference)
2.4L ENGINE
30
°
24'
3.0L ENGINE
28
°
30'
Camber
0
°
00'
±
30' (Left/right deviation within 30')
Caster
3
°
00'
±
30' (Left/right deviation within 30')
Lower arm ball joint breakaway torque N
⋅
m (in-lb)
2.5
−
6.1 (22
−
54)
Stabilizer link ball joint breakaway torque N
⋅
m (in-lb)
3.4
−
9.0 (30
−
80)
BOLT DIAMETER mm (in)
NUMBER OF IDENTIFICATION PROJECTION
Set bolt
16.0 (0.63)
0
Adjusting bolt
14.9 (0.59)
1
14.1 (0.56)
2
13.6 (0.54)
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст