Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 561
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-17
SH O C K A B SO RB ER A SSEM B LY
REMOVAL AND INSTALLATION
M1341002500034
Pre-removal and Post-installation Operation
•
Service Lid Removal and Installation <ECLIPSE> (Refer
to GROUP 52A, Trims
.)
•
Fully Close Convertible Top Assembly <ECLIPSE SPY-
DER>
AC001067AB
1
2
44 ± 5 N·m
33 ± 3 ft-lb
4
3
98 ± 10 N·m
73 ± 7 ft-lb
REMOVAL STEPS
<<A>>
•
DRAIN TURF MOUNTING HOOK
<ECLIPSE SPYDER>
1.
CAP
2.
SHOCK ABSORBER MOUNTING
NUTS
3.
BOLT
>>A<<
4.
SHOCK ABSORBER ASSEMBLY
REMOVAL STEPS (Continued)
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-18
REMOVAL SERVICE POINT
<<A>> DRAIN TURF MOUNTING HOOK REMOVAL
<ECLIPSE SPYDER>
Remove the drain turf mounting hook so that the cap can be
seen from the passenger compartment.
INSTALLATION SERVICE POINT
>>A<< SHOCK ABSORBER ASSEMBLY INSTALLATION
Install the shock absorber so that the larger diameter side of
the lower bushing inner pipe faces toward the outside of the
vehicle.
INSPECTION
M1341002600031
•
Check the rubber parts for cracks and wear.
•
Check the shock absorber for malfunctions, oil leakage, or
abnormal noise.
AC004074AB
REAR GLASS
DRAIN TURF
AC001068
OUTSIDE OF
THE BODY
LOWER
BUSHING
INNER PIPE
AB
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-19
DISASSEMBLY AND ASSEMBLY
M1341005300062
Required Special Tools:
•
MB991237: Spring Compressor Body
•
MB991239: Arm Set
DISASSEMBLY SERVICE POINT
<<A>> JAM NUT REMOVAL
CAUTION
•
To hold the coil spring securely, install special tools
MB991237 and MB991239 evenly, and so that the space
between both arms of the special tool will be maximum
within the installation range.
•
Do not use an impact wrench to tighten the bolt of
special tool MB991237. It will break the special tool.
1. Use special tools MB991237 and MB991239 to compress
the coil spring.
AC003097
N
8
11
12
23 ± 2 N·m
17 ± 1 ft-lb
9
AC
10
7
6
5
4
3
2
1
DISASSEMBLY STEPS
<<A>> >>C<<
1.
JAM NUT
2.
WASHER
3.
UPPER BUSHING A
>>B<<
4.
UPPER BRACKET ASSEMBLY
5.
UPPER SPRING PAD
6.
COLLAR
7.
UPPER BUSHING B
8.
CUP ASSEMBLY
9.
BUMP RUBBER
10. DUST COVER
>>A<<
11. COIL SPRING
12. SHOCK ABSORBER ASSEMBLY
DISASSEMBLY STEPS (Continued)
AC001070
MB991237
MB991239
AB
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-20
WARNING
Do not use an impact wrench to remove the jam nut.
Vibration of the impact wrench will cause special
tools MB991237 and MB991239 to slip. This is
dangerous.
2. While holding the piston rod, remove the jam nut.
ASSEMBLY SERVICE POINTS
>>A<< COIL SPRING INSTALLATION
CAUTION
Do not use an impact wrench to tighten the bolt of special
tool MB991237. It will break the special tool.
1. Install special tools MB991237 and MB991239 in the same
manner as for removal, and compress the coil spring to
install it to the shock absorber
2. Align the edge of the coil spring to the stepped part of the
shock absorber spring seat.
>>B<< UPPER BRACKET ASSEMBLY INSTALLATION
Install the upper bracket assembly so that the lower bushing
inner pipe of the shock absorber is at the position shown.
AC001071
AC001070
MB991237
MB991239
AB
AC001072 AB
COIL SPRING
EDGE
SPRING SEAT
AC001073
LOWER
BUSHING
INNER PIPE
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст