Mitsubishi Galant (2004+). Manual — part 681
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-275
STEP 8. Check intermediate connector A-13, joint
connector (1) C-01 and junction block connector C-214 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC306223
A-13 (GR)
AB
CONNECTOR: A-13
1
4
7
8
2 3
5
13
14
17
15
12
16
11
10
9
6
AC305231
CONNECTOR: C-01
AS
33
22
11
28
17
16
15
14
13
12
25
2324
2627
3
1 2
4 5
21
20
19
18
29 30
32
31
7
6
8
10
9
AC207120
CONNECTOR: C-214
AU
C-214
6
1
7
2
9
8
10
3
5
12
11
4
1314
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-276
STEP 9. Check the harness for open circuit or short circuit
to ground between A/T control relay connector B-16X
terminal 2 in the engine component relay box and junction
block connector C-214 terminal 12.
Q: Is the harness wire in good condition?
YES : Go to Step 15.
NO : Repair or replace the harness wire.
AC306354
RELAY BOX
AB
CONNECTOR: B-16X
2
1
3
4
FRONT OF
VEHICLE
AC207120
CONNECTOR: C-214
AU
C-214
6
1
7
2
9
8
10
3
5
12
11
4
1314
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-277
STEP 10. Measure the A/T control relay output voltage at
PCM connector B-21 by using check harness special tool
MB991923.
(1) Disconnect all the connectors from the PCM.
(2) Connect special tool MB991923 (check harness) between
the PCM and the body-side harness connector.
(3) Turn the ignition switch to the "ON" position.
AC306248AC
B-21
(B)
CONNECTOR: B-21
PCM
AIR
CLEANER
73
80
54
67
60
71 72
77 78 79
64
51
59
58
65
52
66
53
75
74
76
81 82
83
63
JAE
62
68
61
55
69
56
70
57
AC209793AG
SPECIAL TOOL 33-PIN CONNECTOR
(PCM CONNECTOR B-21)
B-21
(GR)
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
PCM
MB991923
BODY SIDE
HARNESS
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-278
(4) Measure the voltage between terminal 57 and ground.
• The measured voltage should equal battery positive
voltage.
(5) Measure the voltage between terminal 70 and ground.
• The measured voltage should equal battery positive
voltage.
(6) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage equal to battery positive
voltage between terminal 57 and ground, and between
terminal 70 and ground?
YES : Go to Step 13.
NO : Go to Step 11.
STEP 11. Check PCM connector B-21 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 12.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC210424
51
58
71
64
77
76
83
70
63
57
73 72
75 74
80
82 81
79 78
54
67
JAE
62
69
56
61
68
55
59
66
60
53
65
52
AC
B-21 HARNESS
CONNECTOR:
COMPONENT SIDE
AC210423
51
58
71
64
77
76
83
70
63
57
73 72
75 74
80
82 81
79 78
54
67
JAE
62
69
56
61
68
55
59
66
60
53
65
52
AC
B-21 HARNESS
CONNECTOR:
COMPONENT SIDE
AC306248AC
B-21
(B)
CONNECTOR: B-21
PCM
AIR
CLEANER
73
80
54
67
60
71 72
77 78 79
64
51
59
58
65
52
66
53
75
74
76
81 82
83
63
JAE
62
68
61
55
69
56
70
57
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст