Mitsubishi Galant (2004+). Manual — part 570
DOOR
TSB Revision
BODY
42-59
>>B<< DOOR OPENING OUTER WEATHERSTRIP
INSTALLATION
Install the door opening outer weatherstrip in the sequence
shown.
.
>>C<< DOOR OPENING INNER WEATHERSTRIP
INSTALLATION
Install the door opening inner weatherstrip in the sequence
shown.
.
AC306359
AC306360
AC306736
<FRONT DOOR>
<REAR DOOR>
AB
2
3
5
1
6
7
4
4
5
2
1
3
AC306361
AC306362
AC306735
<FRONT DOOR>
<REAR DOOR>
AB
1
2
4
4
1
2
3
3
DOOR
TSB Revision
BODY
42-60
>>D<< DOOR WINDOW GLASS RUNCHANNEL
INSTALLATION
Install the door window glass runchannel in the sequence
shown.
AC306363
AC306364
AC306734
<FRONT DOOR>
<REAR DOOR>
AB
1
2
3
4
5
1
2
3
4
5
TRUNK LID
TSB Revision
BODY
42-61
TRUNK LID
TRUNK LID DIAGNOSIS
INTRODUCTION TO TRUNK LID DIAGNOSIS
M1421005800374
Difficult locking and unlocking, uneven clearance and
height, and wind noise from the trunk lid may be
caused by improper adjustment of the trunk lid.
TRUNK LID DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1421005900348
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
trunk lid fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Symptom
Chart.
4. Verify malfunction is eliminated.
SYMPTOM CHART
M1421006000382
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Difficult Locking and Unlocking
DIAGNOSIS
STEP 1. Check the release cable routing
condition.
Q: Is the release cable routing condition good?
YES :
Go to Step 3.
NO :
Repair the release cable routing, then go to
Step 2.
STEP 2. Check the engagement of the trunk lid
latch and trunk lid striker.
Q: Are the trunk lid latch and trunk lid striker engaged
correctly?
YES :
Then go to Step 3.
NO :
Adjust the trunk lid latch. Refer to
STEP 3. Retest the system.
Q: Does the trunk lid lock operate easily?
YES :
The procedure is complete.
NO :
Return to Step 1.
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
Difficult locking and unlocking
1
Uneven body clearance
2
Uneven height
3
TRUNK LID
TSB Revision
BODY
42-62
INSPECTION PROCEDURE 2: Uneven Body Clearance
DIAGNOSIS
STEP 1. Check the clearance around the trunk
lid..
Q: Are the apertures between the trunk lid and the
adjacent body panels aligned correctly?
YES :
Then go to Step 2.
NO :
Adjust the trunk lid panel assembly. Refer to
.
STEP 2. Retest the system.
Q: Are the clearances between the body panels even?
YES :
The procedure is complete.
NO :
Return to Step 1.
INSPECTION PROCEDURE 3: Uneven Height
DIAGNOSIS
STEP 1. Check the trunk lid bumper height.
Q: Is the trunk lid bumper height proper?
YES :
Then go to Step 2.
NO :
Adjust the trunk lid bumper. Refer to
.
STEP 2. Retest the system.
Q: Are the trunk lid and body height even?
YES :
The procedure is complete.
NO :
Return to Step 1.
ON-VEHICLE SERVICE
ADJUSTMENT OF CLEARANCE AROUND TRUNK
LID
M1421008100040
Loosen the trunk lid panel assembly mounting bolt and nut, and
move the trunk lid panel assembly to make the clearance
around the trunk lid even.
AC305824AB
TRUNK LID
HINGE
TRUNK LID PANEL
ASSEMBLY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст