Mitsubishi Galant (2004+). Manual — part 1326
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-997
STEP 6. Using scan tool MB991958, check data list.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following items in the data list. Refer to Data List
Reference Table
a. Item 13: Intake Air Temperature Sensor.
b. Item 25: Barometric Pressure Sensor.
c. Item 21: Engine Coolant Temperature Sensor.
d. Item 69: Right Bank Heated Oxygen Sensor (rear).
e. Item 39: Right Bank Heated Oxygen Sensor (front).
f. Item 59: Left Bank Heated Oxygen Sensor (rear).
g. Item 11: Left Bank Heated Oxygen Sensor (front).
h. Item 27: Power Steering Pressure Switch.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are they operating properly?
YES : Go to Step 7.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
STEP 7. Using scan tool MB991958, check actuator test.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following items in the actuator test. Refer to
Actuator Test Reference Table
a. Item 08: Evaporative Emission Purge Solenoid.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the actuator operating properly?
YES : Go to Step 8.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-998
STEP 8. Check the fuel pressure.
Refer to On-vehicle Service
− Fuel Pressure Test
Q: Is the fuel pressure normal?
YES : a. Check the following items, and repair or replace
the defective items.
• Vacuum leak.
• Broken intake manifold gasket.
• Broken air intake hose.
• Broken vacuum hose.
• Positive crankcase ventilation valve does not
operate.
b. Injector clogged.
Then confirm that the malfunction symptom is
eliminated.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
STEP 9. Check the ignition timing.
Refer to GROUP 11A, On-vehicle Service
− Ignition Timing
Check
Q: Is the ignition timing normal?
YES : Check the following items, and repair or replace the
defective items.
a. Check the ignition coil and spark plugs.
b. Check the purge control system.
c. Check compression pressure.
d. Check if the foreign materials (water,
kerosene, etc.) got into fuel.
e. Check the EGR valve.
Then confirm that the malfunction symptom is
eliminated.
NO : Check that the crankshaft position sensor and timing
belt cover are in the correct position. Then confirm
that the malfunction symptom is eliminated.
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-999
INSPECTION PROCEDURE 9: Idle speed is high (improper idle speed).
.
COMMENT
• In such cases as the above, the cause is proba-
bly that the intake air volume during idle is too
great.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case:)
• Malfunction of the electronic control throttle valve
system.
• Malfunction of the throttle body.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC set?
YES : Refer to Diagnostic Trouble Code Chart
NO : Go to Step 2.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1000
STEP 2. Using scan tool MB991958, check data list.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the following item in the data list. Refer to Data List
Reference Table
a. Item 21: Engine Coolant Temperature Sensor.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 3.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
STEP 3. Using scan tool MB991958, check actuator test.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following item in the actuator test. Refer to
Actuator Test Reference Table
a. Item 08: Evaporative Emission Purge Solenoid.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the actuator operating properly?
YES : Refer to On-vehicle Service
− Throttle Body (Throttle
.
NO : Repair or replace it. Then confirm that the malfunction
symptom is eliminated.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст