Mitsubishi Galant (2004+). Manual — part 923
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-509
DTC SET CONDITIONS
Logic Flow Chart
Check Conditions
• Ignition switch is "ON" position.
Judgement Criteria
• Throttle position sensor (sub) output voltage
should be 4.8 volts or more for 0.5 second.
.
OBD-II DRIVE CYCLE PATTERN
None.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Throttle position sensor failed.
• Open throttle position sensor (sub) circuit, har-
ness damage, or connector damage.
• PCM failed.
START
YES
YES
YES
NO
NO
NO
CONTINUOUS
FAILURE FOR 0.5sec
MALFUNCTION
END
GOOD
OUTPUT VOLTAGE
< =2.25V
OUTPUT VOLTAGE > =4.8V
AK302032
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-510
DIAGNOSIS
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
• MB991658: Test Harness
STEP 1. Using scan tool MB991958, check data list item 14:
Throttle Position Sensor (sub).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Detach the intake air hose at the throttle body.
(4) Disconnect the connector of the throttle position sensor.
(5) Use test harness special tool (MB991658) to connect only
terminals No. 3, No. 4, No. 5, and No. 6.
(6) Set scan tool MB991958 to the data reading mode for item
14, Throttle Position Sensor (sub).
• Output voltage should be between 2.2 and 2.8 volts
when the throttle valve is fully closed with your finger.
• Output voltage should be 4.0 volts or more when the
throttle valve is fully open with your finger.
(7) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Go to Step 2.
STEP 2. Check harness connector B-06 at throttle position
sensor for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 8.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-511
STEP 3. Check the continuity at throttle position sensor
harness side connector B-06.
(1) Disconnect the connector B-06 and measure at the harness
side.
(2) Measure the continuity between terminal No. 3 and ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 7.
NO : Go to Step 4.
STEP 4. Check harness connector B-22 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 8.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
1
6 5 4 3 2
AK203051
B-06 HARNESS
CONNECTOR:
COMPONENT SIDE
AC
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-512
STEP 5. Check for open circuit and harness damage
between throttle position sensor connector B-06 (terminal
No. 3) and PCM connector B-22 (terminal No. 95).
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it. Then go to Step 8.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст