Mitsubishi Galant (2004+). Manual — part 934
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-553
STEP 10. Check for short circuit to ground between
crankshaft position sensor intermediate connector B-119
(terminal No. 2) and PCM connector B-22 (terminal No.
103).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 22.
NO : Repair it. Then go to Step 22.
AK303860
1
2
3
AB
CONNECTOR: B-119
B-119 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-554
STEP 11. Measure the power supply voltage at crankshaft
position sensor intermediate harness side connector
B-119.
(1) Disconnect the connector B-119 and measure at the
harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 1 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 13.
NO : Go to Step 12.
STEP 12. Check harness connector B-17X at MFI relay for
damage.
Q: Is the harness connector in good condition?
YES : Repair harness wire between MFI relay connector
B-17X (terminal No. 4) and crankshaft position sensor
intermediate connector B-119 (terminal No. 1)
because of open circuit or short circuit to ground.
Then go to Step 22.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 22.
AK303860
1
2
3
AB
CONNECTOR: B-119
B-119 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
1
2
3
AK302111
B-119 HARNESS
CONNECTOR:
COMPONENT SIDE
AC
AK303806
2
1
3
4
AB
CONNECTOR: B-17X
B-17X
RELAY BOX
TRIANGLE
MARK
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-555
STEP 13. Check the continuity at crankshaft position
sensor intermediate harness side connector B-119.
(1) Disconnect the connector B-119 and measure at the
harness side.
(2) Check for the continuity between terminal No. 3 and
ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 16.
NO : Go to Step 14.
STEP 14. Check harness connector B-22 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 15.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 22.
AK303806
2
1
3
4
AB
CONNECTOR: B-17X
B-17X
RELAY BOX
TRIANGLE
MARK
HARNESS CONNECTOR:
COMPONENT SIDE
AK302112
1
2
3
AC
B-119 HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-556
STEP 15. Check for open circuit and harness damage
between crankshaft position sensor intermediate
connector B-119 (terminal No. 3) and PCM connector B-22
(terminal No. 113).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 22.
NO : Repair it. Then go to Step 22.
STEP 16. Check harness connector B-17X at the MFI relay
for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 17.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 22.
AK303860
1
2
3
AB
CONNECTOR: B-119
B-119 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK303806
2
1
3
4
AB
CONNECTOR: B-17X
B-17X
RELAY BOX
TRIANGLE
MARK
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст