Mitsubishi Galant (2004+). Manual — part 1167
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-361
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 3 minutes or more have passed since the engine
starting sequence was completed.
• Left bank heated oxygen sensor (rear) signal
voltage has continued to be 0.15 volt or lower.
• Engine coolant temperature is higher than 76°C
(169
°F).
• Engine speed is higher than 1,200 r/min.
• Volumetric efficiency is higher than 25 percent.
• Monitoring time: 7 seconds.
START
V
F
> =4.5V
2secs HAS PASSED
YES
YES
YES
NO
NO
NO
MALFUNCTION
MONITORING
CONDITIONS
YES
NO
MONITORING
CONDITIONS
+5V ON
AK302398
V
F
< 0.15V
10secs HAS PASSED
YES
YES
NO
NO
END
MALFUNCTION
GOOD
MODULATE A/F CONDITION TO RICH
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-362
Judgment Criteria
• Input voltage supplied to the PCM interface circuit
is higher than 4.5 volts when 5 volts is applied to
the left bank heated oxygen sensor (rear) output
line via a resistor.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
− Other Monitor
.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )
• Left bank heated oxygen sensor (rear) failed.
• Open or shorted circuit in left bank heated oxy-
gen sensor (rear) output line, or harness dam-
age.
• Open circuit in left bank heated oxygen sensor
(rear) ground line, or harness damage.
• Connector damage.
• PCM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
• MB991316: Test Harness
• MB991923: Power Plant ECU Check Harness
STEP 1. Using scan tool MB991958, check data list item 59:
Left Bank Heated Oxygen Sensor Bank 2, Sensor 2 (left
rear).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
59, Heated Oxygen Sensor Bank 2, Sensor 2 (left rear).
• Warming up the engine. When the engine is revved, the
output voltage should repeat 0 volt and 0.6 to 1.0 volt
alternately.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Go to Step 2.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-363
STEP 2. Measure the sensor output voltage at left bank
heated oxygen sensor (rear) connector B-24 by
backprobing.
(1) Do not disconnect the connector B-24.
(2) Start the engine and run at idle.
(3) Measure the voltage between terminal No. 4 and ground by
backprobing.
• Warming up the engine. When the engine is revved, the
output voltage should repeat 0 volt and 0.6 to 1.0 volt
alternately.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage within the specified range?
YES : Go to Step 3.
NO : Go to Step 7.
1
2
3
4
AK303079
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-24
AB
LEFT BANK
HEATED OXYGEN
SENSOR (REAR)
B-24 (GR)
1 2
4
3
AK201407
B-24 HARNESS
CONNECTOR:
HARNESS SIDE
AD
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-364
STEP 3. Measure the sensor output voltage at PCM
connector B-22 by using power plant ECU check harness
special tool MB991923.
(1) Disconnect the all PCM connectors and connect power
plant ECU check harness special tool MB991923 between
the separated connectors.
(2) Start the engine and run at idle.
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK202956
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
AB
POWER PLANT ECU
CHECK HARNESS CONNECTOR
MB991923
PCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст