Mitsubishi Galant (2004+). Manual — part 1449
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-39
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
General service tool
(jumper)
Making voltage and
resistance
measurements during
troubleshooting
A: Connect pin contact
pressure inspection
B: Power circuit
inspection
C: Power circuit
inspection
D: Commercial tester
connection
TOOL
TOOL NUMBER
AND NAME
REPLACED BY
MILLER TOOL
NUMBER
APPLICATION
MB991223
A
D
C
B
AF
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-40
ON-VEHICLE SERVICE
HOW TO REGISTER ENCRYPTED CODE
M1543008100443
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness A (Vehicles with CAN
communication system)
CAUTION
Because registering the encrypted codes is done after all
previously-registered codes have been erased, you should
keep all of the ignition keys that have already been regis-
tered accessible.
If the ignition key, immobilizer-ECU, PCM is replaced,
encrypted codes of all the ignition keys must be registered. (A
maximum of eight different ignition key can be registered).
Moreover, when the immobilizer-ECU has been replaced, you
will need to use scan tool MB991958 to register the immobi-
lizer-ECU and input the vehicle secret code.
If an attempt is made to start the engine with an unregistered
ignition key, cranking occurs, but fuel supply is cut off to disable
the engine. In approx. 10 seconds, the immobilizer indicator will
blink for approx. 30 seconds.
NOTE: PCM has an encrypted code for immobilizer-ECU, and
the encrypted code is registered in the immobilizer-ECU and
ignition key.
POINTS TO NOTE DURING OPERATION
If none of the functions can be used, check the diagnostic trou-
ble codes, and after carrying out any necessary repairs, repeat
the operation. If an incorrect password is input five times in a
row, the immobilizer-ECU judges that an unauthorized opera-
tion is being attempted. Start-prevention mode will be set, and
engine operation will stop and all special functions will be dis-
abled. If the ignition switch is turned to "ON" position and left in
that position for approximately 16 minutes, "Unauthorized oper-
ation, start- prevention mode" will be cancelled.
AC307460
AB
IMMOBILIZER INDICATOR LIGHT
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-41
KEY ID REGISTRATION
All ignition keys can be registered with scan tool MB991958.
Additional ignition keys can be registered with or without scan
tool MB991958.
.
Registration with the scan tool
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to "LOCK" (OFF) position before connect-
ing or disconnecting scan tool MB991958.
NOTE:
.
•
Before registration, check that no DTC code is set. If a DTC
code is set, resolve the problem beforehand.
•
Using the key ID register function will cause all key IDs that
have been previously registered in the immobilizer-ECU to
be erased. All keys need to be registered. Those which
have been registered before should be on hand before
using this function.
•
If registering more than one key, do not disconnect scan
tool MB991958 halfway through the registration process.
•
After registering key IDs, check that the engine can be
started using all of the keys that have been registered. If the
engine will not start, refer to Immobilizer System Diagnosis
.
1. Connect the scan tool MB991958 to the data link connector.
2. Turn the ignition switch to "ON" position.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-42
3. Select "Interactive Diagnosis" from the start-up screen.
4. Select "System select."
5. Choose "IMMOBILIZER" from the "POWER TRAIN" tab.
6. Choose "Special Function" from "IMMOBILIZER" screen.
7. Choose "Key registration" from "Special Function" screen.
TIR
Technical Information
Retrleval
Interactive
Diagnosis
Tutorial
Maintenance
Power Down
AC207295
AB
System select
Special function
CAN bus diagnosis
Function Select Menu
Menu
AC209666
Maintenance
AC
MFI
ELC-A/T
IMMOBILIZER
SS4II
CRUISE CNTRL
CHASSIS
BODY
System Select Menu
POWER TRAIN
AC209667
AC
Check Chart For
Problem Sy
Data List
Special
Function
Self-diagnosis
Voltmeter
Simulated Vehicle
Speed Out
Drive Recorder
Resistor
POWERTRAIN
IMMOBILIZER
IMMOBILIZER
AC207298
AD
Key registration
Transponder ID
addition
POWERTRAIN
Special Function
IMMOBILIZER
Special Function
AC207299
AE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст