Mitsubishi Galant (2004+). Manual — part 254
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-207
STEP 12. Check the wiring harness between power
window main switch connector E-12 (terminals 3 and 11)
and front power window sub switch connector E-04
(terminals 8 and 5).
NOTE: Also check intermediate connectors C-12 and C-26. If
intermediate connector C-12 or C-26 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between power window main
switch connector E-12 (terminals 3 and 11) and front
power window sub switch connector E-04 (terminals 8
and 5) in good condition?
YES : Replace the power window main switch. When the
front power window sub switch (RH) is operated, the
front power window (RH) should raise and lower
normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
front power window sub switch (RH) is operated, the
front power window (RH) should raise and lower
normally.
AC305262
3
9
4
12
14
6
13
5
1110
8
2
7
1
HARNESS SIDE
CONNECTOR:E-12
AC
AC305333
CONNECTOR:E-04
AC
HARNESS SIDE
AC305233
CONNECTOR:C-12
AB
AC305231AC
CONNECTOR:C-26
HARNESS SIDE
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-208
STEP 13. Check the wiring harness between front power
window sub switch connector E-04 (terminals 4 and 6) and
front power window regulator motor (RH) connector E-03
(terminals 1 and 2).
Q: Is the wiring harness between front power window sub
switch connector E-04 (terminals 4 and 6) and front
power window regulator motor (RH) connector E-03
(terminals 1 and 2) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
front power window sub switch (RH) is operated, the
front power window (RH) should raise and lower
normally.
STEP 14. Check rear power window sub switch (LH)
connector E-17 and rear power window regulator motor
(LH) connector E-16 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are rear power window sub switch (LH) connector E-17
and rear power window regulator motor (LH) connector
E-16 in good condition?
YES : Go to Step 15.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. When the rear power window sub switch
(LH) is operated, the rear power window (LH) should
raise and lower normally.
AC305333
E-03(GR)
E-04
CONNECTORS:E-03,E-04
AB
HARNESS SIDE
E-03
E-04
HARNESS SIDE
AC305262
CONNECTORS:E-16,E-17
AF
E-16
E-17
HARNESS SIDE
E-17
E-16(GR)
HARNESS SIDE
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-209
STEP 15. Check the rear power window sub switch (LH) for
continuity.
(1) Remove the rear power window sub switch (LH). Refer to
GROUP 42, Door, Door Glass and Regulator
.
(2) Check continuity when the rear power window sub switch
(LH) is operated to "UP" or "DOWN" position.
Q: Is the rear power window sub switch (LH) normal?
YES : Go to Step 16.
NO : Replace the rear power window sub switch (LH).
When the rear power window sub switch (LH) is
operated, the rear power window (LH) should raise
and lower normally.
STEP 16. Check the rear power window regulator motor
(LH).
(1) Remove the rear power window regulator assembly (LH).
Refer to GROUP 42, Door, Door Glass and Regulator
(2) Connect a battery to the motor terminal, and check that the
motor runs freely.
Q: Is the rear power window regulator motor (LH) normal?
YES : Go to Step 17.
NO : Replace the rear power regulator assembly (LH).
When the rear power window sub switch (LH) is
operated, the rear power window (LH) should raise
and lower normally.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
UP
4
− 5, 6 − 7
Less than 2 ohms
OFF
4
− 5, 7 − 8
DOWN
4
− 6, 7 − 8
AC210747
8
3
1
4 5 6
2
7
AB
<REAR>
BATTERY CONNECTION
SLIDER POSITION
• Connect terminal 1 to the
negative battery terminal
• Connect terminal 2 to the
positive battery terminal
UP
• Connect terminal 2 to the
negative battery terminal
• Connect terminal 1 to the
positive battery terminal
DOWN
1 2
AC206013AB
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-210
STEP 17. Check the battery power supply circuit to the rear
power window sub switch (LH). Measure the voltage at rear
power window sub switch (LH) connector E-17.
(1) Disconnect rear power window sub switch (LH) connector
E-17 and measure the voltage available at the wiring
harness side of the connector.
(2) Measure the voltage between terminal 6 and ground.
• The voltage should measure approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 20.
NO : Go to Step 18.
STEP 18. Check power window relay connector C-203 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is power window relay connector C-203 in good
condition?
YES : Go to Step 19.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. When the rear power window sub switch
(LH) is operated, the rear power window (LH) should
raise and lower normally.
AC305262
HARNESS SIDE
CONNECTOR:E-17
AG
AC209365EI
CONNECTOR E-17
(HARNESS SIDE)
AC305415 AC
JUNCTION BLOCK SIDE
CONNECTOR:C-203
JUNCTION BLOCK
(FRONT VIEW)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст