Mitsubishi Galant (2004+). Manual — part 575

SUNROOF ASSEMBLY

TSB Revision

BODY

42-79

SUNROOF INITIALIZATION

M1426004600123

The sunroof should be initialized when any of the following
components are replaced, the sunroof position is miss timed.

• Roof lid glass assembly

• Sunroof motor assembly

1. Ensure the components are correctly assembled. Ensure all

the connectors are connected securely.

2. If the sunroof is already in learn mode, go to step 3. If the

sunroof is not in learn mode, enter learn mode by (1) or (2)
below.

(1) Disconnect the sunroof motor assembly connector while

the sunroof is operating.

(2) Stop the sunroof operation by fitting the block (board

etc.). Then press and hold the sunroof close switch for 10
seconds with the sunroof stopped.

3. Press the sunroof Close switch repeatedly until the sunroof

is tilted up fully.

4. Press and hold the sunroof Close switch for at least three

seconds.

5. Press the sunroof Close switch until the sunroof closes fully.
6. The sunroof should work normally.
NOTE: Do not stop the sunroof before it reaches the fully
closed position during operations in steps 5 above. If the sun-
roof has stopped accidentally, repeat the procedure from step
1.

AC203084 AB

SUNROOF ASSEMBLY

TSB Revision

BODY

42-80

SUNROOF OPERATION CHECK

M1426002600332

CAUTION

Check that the following items are normal before carrying out this operation check.

• Installation condition of the sunroof assembly
• Installation condition, deformation and contamination of the sunroof drive cable
• Installation of sunroof lid glass
• Sunroof switch and sunroof motor assembly

Check that the following items. If faulty, replace the
sunroof motor assembly.

AC209094

AC306500

AC306368

SUNROOF SWITCH

OPEN

TILT-UP

CLOSE/TILT-DOWN

OVERHEAD CONSOLE

SUNROOF ASSEMBLY

TSB Revision

BODY

42-81

Basic operation

NO. SUNROOF

FUNCTION

REQUIREMENTS FOR THE SUNROOF TO
FUNCTION

NORMAL OPERATION

OPEN

1. Ignition switch: ON
2. Sunroof switch: OPEN

The sunroof opens fully and
automatically and stops
several centimeters forward
of the fully open position
(position for less wind
noise).
Then, when the sunroof
switch is operated again,
the sunroof opens further to
fully open position.

1. Ignition switch: ON
2. Sunroof switch: CLOSE/TILT-DOWN

The sunroof closes while
the sunroof switch is
pushed to the
CLOSE/TILT-DOWN
position.

TILT-UP

1. Ignition switch: ON
2. Sunroof switch: TILT-UP

The sunroof tilts up fully and
automatically.

TILT-DOWN

1. Ignition switch: ON
2. Sunroof switch: CLOSE/TILT-DOWN

The sunroof closes while
the sunroof switch is
pushed to the
CLOSE/TILT-DOWN
position.

AUTOMATIC
OPERATION
INTERRUPTION
(OPEN)

1. Ignition switch: ON
2. Sunroof switch: OPEN or TILT-UP

The sunroof stops the
automatic opening
operation.

1. Ignition switch: ON
2. Sunroof switch: CLOSE/TILT DOWN (Push

the sunroof switch to the
CLOSE/TILT-DOWN position while the
sunroof is automatically opening and
release the switch within two seconds)

The sunroof stops the
automatic opening
operation.

1. Ignition switch: ON
2. Sunroof switch: CLOSE/TILT DOWN (Push

the sunroof switch to the
CLOSE/TILT-DOWN position more than
two seconds while the sunroof is
automatically opening)

The sunroof stops the
automatic opening
operation, and the sunroof
closes while the sunroof
switch is pushed to the
CLOSE/TILT-DOWN
position.

AUTOMATIC
OPERATION
INTERRUPTION
(TILT-UP)

1. Ignition switch: ON
2. Sunroof switch: OPEN or TILT-UP, CLOSE/TILT

DOWN

The sunroof stops the
automatic opening
operation.

SUNROOF ASSEMBLY

TSB Revision

BODY

42-82

Sunroof timer mechanism

In cases except the following, the basic operation
and jam preventing mechanism will be maintained
for thirty seconds after the ignition switch is turned to
the LOCK (OFF) position. (Sunroof timer function)

• If you open a door within that period (i.e. a door

switch is on), the sunroof timer function will be
cancelled immediately.

• If you turn the ignition switch to the LOCK (OFF)

position while the timer is working, the sunroof
will continue moving until it closes fully, regard-
less of the time-out period.

SUNROOF ASSEMBLY

REMOVAL AND INSTALLATION

M1426001200308

WARNING

When removing and installing the front passenger seat, be sure to carry out accuracy check
occupant classification sensor after the seat has been installed in the vehicle. (Refer to
GROUP 52B, On-Vehicle Service

P.52B-354

Post-installation Operation <Roof lid glass assembly,
Sunroof assembly>
• Sunroof Water Test (Refer to

P.42-77

• Sunroof Fit Adjustment (Refer to

P.42-78

Post-installation Operation <Roof lid glass assembly,
Sunroof motor assembly>
• Sunroof Initializing Adjustment (Refer to

P.42-79

AC307032

AC307985

AC206389