Mitsubishi Galant (2004+). Manual — part 708
ON-VEHICLE SERVICE
TSB Revision
AUTOMATIC TRANSAXLE
23A-383
(4) Loosen the bolt fixing the shift lock cable unit, push the
lever in direction B and the unit in direction C and tighten
the bolt at the standard torque.
Tightening torque: 5.0
± 1.0 N⋅m (44 ± 9 in-lb)
(5) Lift the lock guide of the key interlock cable and then
unlock it.
(6) Lower the lock guide of the key interlock cable and then
lock it.
NOTE: The key interlock cable is adjusted according to
the lock position (cap push state) at this time. Readjust
the lock position if key interlocking operations malfunction
after locking.
3. After adjustment, re-check the operations. Replace the key
interlock cable and shift lock cable unit if operations are
defective. (Refer to
TRANSAXLE CONTROL CABLE ADJUSTMENT
M1231028000064
1. Move the selector lever to the "N" position.
2. Loosen the upper control lever adjusting nut.
3. Gently push the transaxle control cable in the direction of the
arrow, and then tighten the adjusting nut.
Tightening torque: 12
± 2 N⋅m (107 ± 17 in-lb)
4. Check that the transaxle shifts to the correct range
corresponding to the position of the selector lever, and that it
functions correctly in that range.
AC000004AG
LOCK
UNLOCK
LOCK GUIDE
KEY INTERLOCK CABLE
CAP
LEVER
FIXING BOLT
SHIFT LOCK CABLE UNIT
C
A
B
VIEW A
AC305881
AC305532
AC305679
<F4A4B>
MANUAL CONTROL LEVER
MANUAL CONTROL LEVER
<F4A5A>
ADJUSTING NUT
12 ± 2 N·m
107 ± 17 in-lb
ADJUSTING NUT
12 ± 2 N·m
107 ± 17 in-lb
AE
TRANSAXLE CONTROL
TSB Revision
AUTOMATIC TRANSAXLE
23A-384
TRANSAXLE CONTROL
REMOVAL AND INSTALLATION
M1231006600369
WARNING
•
When removing and installing the transaxle control cable and shift lock cable unit, be
careful not to hit the SRS-ECU.
•
When removing and installing the front passenger seat, be sure to carry out accuracy
check occupant classification sensor after the seat has been installed in the vehicle.
(Refer to GROUP 52B, On-Vehicle Service
AC305533AB
1
12 ± 2 N·m
107 ± 17 in-lb
<F4A5A>
<F4A4B>
2
2
5
6
8
3
12 ± 2 N·m
102 ± 22 in-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
12 ± 2 N·m
102 ± 22 in-lb
4
7
7
TRANSAXLE CONTROL
CABLE ASSEMBLY REMOVAL
STEPS
•
AIR DUCT AND AIR CLEANER
ASSEMBLY (REFER TO GROUP
15
•
BATTERY AND BATTERY TRAY
•
POWERTRAIN CONTROL
MODULE (PCM) (REFER TO
GROUP 13A
.)
•
HEATER UNIT AND DECK
CROSSMEMBER ASSEMBLY
(REFER TO GROUP 55,
HEATER UNIT, HEATER CORE,
BLOWER ASSEMBLY AND
EVAPORATOR UNIT
>>B<<
1.
ADJUSTING NUT
>>B<<
2.
TRANSAXLE CONTROL CABLE
ASSEMBLY CONNECTION
(TRANSAXLE SIDE)
>>A<<
3.
SHIFT LOCK CABLE UNIT
4.
TRANSAXLE CONTROL CABLE
ASSEMBLY CONNECTION
(SELECTOR LEVER ASSEMBLY
SIDE)
5.
TRANSAXLE CONTROL CABLE
ASSEMBLY
SELECTOR LEVER ASSEMBLY
ASSEMBLY REMOVAL STEPS
•
FLOOR CONSOLE (REFER TO
GROUP 52A, FLOOR CONSOL
ASSEMBLY
)
>>A<<
3.
SHIFT LOCK CABLE UNIT
4.
TRANSAXLE CONTROL CABLE
ASSEMBLY CONNECTION
(SELECTOR LEVER ASSEMBLY
SIDE)
TRANSAXLE CONTROL
CABLE ASSEMBLY REMOVAL
STEPS (Continued)
TRANSAXLE CONTROL
TSB Revision
AUTOMATIC TRANSAXLE
23A-385
INSTALLATION SERVICE POINTS
.
>>A<< SHIFT LOCK CABLE UNIT INSTALLATION
1. Selector lever to "P" position.
2. Turn the ignition key to "LOCK" (OFF) position.
3. Install the rod of the shift lock cable unit to the lock cam,
push the lever in direction A, push the shift lock cable unit in
direction B and tighten the bolt at the standard torque.
Tightening torque: 5.0
± 1.0 N⋅m (44 ± 9 in-lb)
4. Check the selector lever operation.(Refer to
.
>>B<< ADJUSTING NUT/TRANSAXLE CONTROL CABLE
(TRANSAXLE SIDE) INSTALLATION
1. Place the selector lever and manual control lever in the "N"
position.
2. Place the cable stud into the manual control lever slot and
install the nut loosely. Gently push the transaxle control
cable into the manual control lever slot until the cable is taut.
Tighten the nut to the specified torque.
Tightening torque: 12
± 2 N⋅m (107 ± 17 in-lb)
6.
A/T SELECTOR LEVER POSITION
ILLUMINATION LIGHT HARNESS
CONNECTOR <VEHICLES
WITHOUT SPORT MODE>,
SHIFT SWITCH ASSEMBLY
HARNESS CONNECTOR
<VEHICLES WITH SPORT
MODE>
7.
HARNESS CILP CONNECTION
8.
SELECTOR LEVER ASSEMBLY
SELECTOR LEVER ASSEMBLY
ASSEMBLY REMOVAL STEPS
AC308762
SHIFT LOCK
CABLE UNIT
AB
LOCK CAM
LEVER
BOLT
ROD
A
B
AC305881
AC305532
AC305679
<F4A4B>
MANUAL CONTROL LEVER
MANUAL CONTROL LEVER
<F4A5A>
ADJUSTING NUT
12 ± 2 N·m
107 ± 17 in-lb
ADJUSTING NUT
12 ± 2 N·m
107 ± 17 in-lb
AE
TRANSAXLE CONTROL
TSB Revision
AUTOMATIC TRANSAXLE
23A-386
INSPECTION
M1231030000094
Check the cable assembly for function and for damage.
DISASSEMBLY AND ASSEMBLY
M1231006800363
<VEHICLES WITHOUT SPORT MODE>
AC306189
2
3
4
1
6
6
7
2.0 ± 0.3 N·m
18 ± 2 in-lb
AB
5
DISASSEMBLY STEPS
1.
SHIFT KNOB
2.
PUSH BUTTON
3.
SPRING
4.
INDICATOR PANEL
5.
A/T SELECTOR LEVER
POSISITION ILLUMINATION
LIGHT
6.
BRACKET STAY
7.
SHIFT LEVER ASSEMBLY
DISASSEMBLY STEPS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст