Mitsubishi Galant (2004+). Manual — part 419
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-287
STEP 26. Check ABS-ECU connector A-02 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Is ABS-ECU connector A-02 in good condition?
YES : Go to Step 27.
NO : Repair the damaged parts.
AC305206
CONNECTOR: A-02
AG
A-02 (GR)
HARNESS SIDE
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-288
STEP 27. Check the CAN_H line (communication line only)
between intermediate connector C-29 and ABS-ECU
connector for short to ground. Measure the resistance at
intermediate connector C-29.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect intermediate connector C-29 and ABS-ECU
connector A-02, and measure the resistance at the male
side of intermediate connector C-29 (at front wiring harness
side).
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
.
(3) Disconnect the negative battery terminal.
(4) Measure the resistance between intermediate connector
terminal 11 and body ground.
OK: 1 k
Ω or more
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the resistance measure 1 k
Ω or more?
YES : If the resistance measures 1 k
Ω or more, go to Step
28 .
NO : If the resistance measures less than 1 k
Ω, repair the
wiring harness between intermediate connector C-29
and ABS-ECU connector.
AC305206
CONNECTOR: A-02
AG
A-02 (GR)
HARNESS SIDE
AC305231AI
CONNECTOR: C-29
AC209364
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC209364
MALE SIDE: C-29
TEST
HARNESS
HV
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-289
STEP 28. Check the CAN_H line (communication line only)
between the powertrain control module connector and
ABS-ECU connector for short to ground. Measure the
resistance at powertrain control module connector B-19.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect powertrain control module connector B-19 and
ABS-ECU connector A-02, and measure the resistance at
the harness side of powertrain control module connector
B-19.
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
.
(3) Disconnect the negative battery terminal.
AC305206
CONNECTOR: A-02
AG
A-02 (GR)
HARNESS SIDE
AC306248AD
B-19 (B)
CONNECTOR: B-19
PCM
AIR
CLEANER
HARNESS SIDE
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-290
(4) Measure the resistance between powertrain control module
connector terminal 17 and body ground.
OK: 1 k
Ω or more
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the resistance measure 1 k
Ω or more?
YES : If the resistance measures 1 k
Ω or more, go to Step
29 .
NO : If the resistance measures less than 1 k
Ω, repair the
wiring harness between powertrain control module
connector and ABS-ECU connector.
AC209364
HARNESS SIDE: B-19
TEST
HARNESS
AC209364IE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст