Mitsubishi Galant (2004+). Manual — part 1009
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-853
STEP 2. Check the throttle actuator control motor.
(1) Disconnect the connector B-06.
(2) Measure the resistance between throttle actuator control
motor side connector terminals No. 1 and No. 2.
Standard value: 0.3
− 80 ohms [at 20°C (68°F)]
Q: Is the measured resistance between 0.3 and 80 ohms [at
20
°C (68°F)]?
YES : Go to Step 3.
NO : Replace the throttle body assembly. Then go to Step
STEP 3. Check harness connector B-23 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 7.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
6
1 2 3 4 5
AK202992
THROTTLE ACTUATOR
CONTROL MOTOR
CONNECTOR
AB
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-854
STEP 4. Check for short circuit to ground between throttle
actuator control motor connector B-06 (terminal No. 1) and
PCM connector B-23 (terminal No. 147).
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair it. Then go to Step 7.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-855
STEP 5. Check for short circuit to ground between throttle
actuator control motor connector B-06 (terminal No. 2) and
PCM connector B-23 (terminal No. 141).
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it. Then go to Step 7.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-856
STEP 6. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P2102 set?
YES : Replace the PCM. Then go to Step 7.
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
STEP 7. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P2102 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст