Mitsubishi Galant (2004+). Manual — part 1382
ON-VEHICLE SERVICE
TSB Revision
FRONT SUSPENSION
33-7
4. Use a turning radius gauge to check that the steering angle
is at the standard value.
STEERING ANGLE
Standard value:
.
CAMBER, CASTER AND KINGPIN INCLINATION
Required Special Tool:
• MB991004: Wheel Alignment Gauge Attachment
Standard value:
Camber: 0
° 00' ± 30' (Left/right deviation within 30')
Caster: 3
° 00' ± 30' (Left/right deviation within 30')
Kingpin inclination: 12
° 54' ± 1° 30'
NOTE: Caster are preset at the factory and cannot be adjusted.
CAUTION
Never subject the wheel bearings to the vehicle load when
the drive shaft nuts are loosened.
NOTE: Attach the camber/caster/kingpin gauge to the drive-
shaft by using special tool MB991004. Tighten special tool
MB991004 to the same torque 226
±
29 N
⋅
m (167
±
21 ft-lb) as
the drive shaft nut.
If the camber is outside of the standard value, perform the fol-
lowing adjustment procedures.
1. Estimate how much additional camber adjustment is
required. Using the table below, select the camber adjusting
bolt, and then replace the knuckle and strut assembly
connection bolts (upper bolt, lower bolt) with the selected
bolts.
ITEM
VEHICLES WITH
16-INCH
WHEELS
VEHICLES WITH
17-INCH
WHEELS
Inner wheel
37
°12' ± 2°00'
33
°48' ± 2°00'
Outer wheel
(reference)
30
°18'
28
°18'
BOLT DIAMETER
mm (in)
CAMBER ADJUSTING VALUE
0
°15' 0°30' 0°45' 1°00' 1°15' 1°30'
Upper
bolt
16.0 (0.63) •
•
14.9 (0.59)
•
•
14.1 (0.56)
•
13.6 (0.54)
•
AC001079
MB991004
AB
AC001080
STRUT
ASSEMBLY
LOWER BOLT
UPPER BOLT
KNUCKLE
AB
ON-VEHICLE SERVICE
TSB Revision
FRONT SUSPENSION
33-8
NOTE: If the camber adjusting value that is required is greater
than 1
°
30', check for bent or damaged parts and replace as
necessary.
Bolts are identified in the following table:
NOTE: Set bolt is the bolt installed at factory. "10" embossed
on bolt head is head mark.
2. Tighten the nuts temporarily, and then pull or push the front
axle to adjust the camber.
NOTE: Pulling the upper side of the front axle to the outside
of the vehicle will increase the camber. Pushing it to the
inside of the vehicle will decrease the camber.
3. Tighten the nuts to 305
± 25 N⋅m (225 ± 18 ft-lb).
4. Recheck the camber.
LOWER ARM BALL JOINT END PLAY CHECK
M1332011300085
1. Raise the vehicle.
2. Move the lower arm up and down with your hands to check
for excessive play in the axial direction of the ball joint. If
there is excessive play, replace the lower arm assembly.
BALL JOINT DUST COVER CHECK
M1332008600354
1. Press the dust cover with your finger to check that there are
no cracks or damage in the dust cover.
2. If the dust cover is cracked or damaged, replace the lower
arm assembly or the stabilizer link.
NOTE: If the dust cover is cracked or damaged, it is possible
that there may also be damage to the ball joint.
Lower
bolt
16.0 (0.63) •
14.9 (0.59)
•
•
14.1 (0.56)
•
•
13.6 (0.54)
•
DIAMETER A mm (in)
NUMBER OF IDENTIFICATION
PROJECTION
Set bolt
16.0 (0.63) 0
Adjusting
bolt
14.9 (0.59) 1
14.1 (0.59) 2
13.6 (0.54) 3
BOLT DIAMETER
mm (in)
CAMBER ADJUSTING VALUE
0
°15' 0°30' 0°45' 1°00' 1°15' 1°30'
AC001081 AB
A
A
HEAD MARK
IDENTIFICATION
PROJECTION
AC001082
305 ± 25 N·m
225 ± 18 ft-lb
AE
STRUT ASSEMBLY
TSB Revision
FRONT SUSPENSION
33-9
STRUT ASSEMBLY
REMOVAL AND INSTALLATION
M1332001100358
INSPECTION
M1332001200281
• Check for oil leaks from the strut assembly.
• Check the strut assembly for damage or deformation.
Post-installation Operation
• Front Wheel Alignment Check and Adjustment (Refer to
).
AC205769
48 ± 7 N·m
36 ± 5 ft-lb
1
2
3
4
AC
305 ± 25 N·m
225 ± 18 ft-lb
6
48 ± 7 N·m
36 ± 5 ft-lb
5
REMOVAL STEPS
1.
STABILIZER LINK
2.
BRAKE HOSE BRACKET
3.
FRONT WHEEL SPEED SENSOR
CLAMP <VEHICLES WITH ABS>
4.
STRUT BOLT
5.
STRUT NUT
•
STRUT TOWER BAR BRACKET
<GTS> (REFER TO GROUP 42,
STRUT TOWER BAR
).
6.
STRUT ASSEMBLY
REMOVAL STEPS (Continued)
STRUT ASSEMBLY
TSB Revision
FRONT SUSPENSION
33-10
DISASSEMBLY AND ASSEMBLY
M1332001300352
Required Special Tools:
• MB991680: Wrench Set
• MB991681: Wrench
• MB991682: Socket
• MB991832: Spring Compressor Set
• MB991793: Spring Compressor
• MB991794: Upper Plate
• MB991795: Attachment A
• MB991829: Arm Bracket
• MB991830: Fixture
• MB991831: Spacer
DISASSEMBLY SERVICE POINTS
.
<<A>> STRUT NUT (SELF-LOCKING NUT) REMOVAL
1. Install special tool MB991795 to special tool MB991793 as
shown in the illustration.
AC305783
7
8
9
10
1
2
3
4
5
6
65 ± 5 N·m
48 ± 4 ft-lb
AB
DISASSEMBLY STEPS
<<A>> >>C<<
1.
STRUT NUT (SELF-LOCKING NUT)
>>B<<
2.
STRUT INSULATOR
3.
STRUT BEARING
4.
SPRING UPPER SEAT
5.
SPRING UPPER PAD
6.
STRUT COVER
7.
STRUT DAMPER
8.
COIL SPRING
>>A<<
9.
SPRING LOWER PAD
<<B>>
10. FRONT SUSPENSION STRUT
AC105115 AE
MB991795
MB991793
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст