Mitsubishi Galant (2004+). Manual — part 358
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-43
STEP 11. Check the CAN_H line (communication line only)
between joint connector (3) and ETACS-ECU connector for
a short to the power supply. Measure the voltage at joint
connector (3) C-02.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (3) C-02 and ETACS-ECU
connector C-218, and measure the voltage at the wiring
harness side of joint connector (3) C-02.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between joint connector (3) terminal 5
and body ground.
OK: 1.0 V or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the voltage measure 1.0 V or less?
YES : If the voltage measures 1.0 V or less, diagnose CAN
bus lines thoroughly by referring to
NO : If the voltage measures more than 1.0 V, repair the
wiring harness between joint connector (3) and the
ETACS-ECU connector.
AC305231AP
CONNECTOR: C-02
AC305413
C-218 (GR)
CONNECTOR: C-218
AI
HARNESS SIDE
JUNCTION BLOCK
(REAR VIEW)
68
74
63
66
72
73
67
65 64
61
70
71
62
69
60
57
58
59
56 55
52
54 53
51
AC209365
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC209365
AC209365
HARNESS SIDE: C-02
TEST HARNESS
FR
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-44
STEP 12. Check the CAN_H line (communication line
including the A/C-ECU) between joint connector (3) and
the A/C-ECU connector for a short to the power supply.
Measure the voltage at joint connector (3) C-02.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (3) C-02, and measure the
voltage at the wiring harness side of joint connector (3)
C-02.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between joint connector (3) terminal 6
and body ground.
OK: 4.0 V or less
Q: Does the voltage measure 4.0 V or less?
YES : If the voltage measures 4.0 V or less, go to Step 15.
NO : If the voltage measures more than 4.0 V, go to Step
13.
AC305231AP
CONNECTOR: C-02
AC209365
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC209365
AC209365
HARNESS SIDE: C-02
FS
TEST HARNESS
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-45
STEP 13. Check A/C-ECU connector C-10 <manual air
conditioning system (low)> or C-15 <manual air
conditioning system (middle) or automatic air conditioning
system> for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Is A/C-ECU connector C-10 <manual air conditioning
system (low)> or C-15 <manual air conditioning system
(middle) or automatic air conditioning system> in good
condition?
YES : Go to Step 14.
NO : Repair the damaged parts.
AC305234AB
C-10 HARNESS SIDE
C-15 HARNESS SIDE
CONNECTORS: C-10, C-15
C-10 (B)
C-15 (B)
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-46
STEP 14. Check the CAN_H line (communication line only)
between joint connector (3) and A/C-ECU connector for a
short to the power supply. Measure the voltage at joint
connector (3) C-02.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (3) C-02 and A/C-ECU
connector C-10 <manual air conditioning system (low)> or
C-15 <manual air conditioning system (middle) or automatic
air conditioning system>, and measure the voltage at the
wiring harness side of joint connector (3) C-02.
(2) Turn the ignition switch to the "ON" position.
AC305231AP
CONNECTOR: C-02
AC305234AB
C-10 HARNESS SIDE
C-15 HARNESS SIDE
CONNECTORS: C-10, C-15
C-10 (B)
C-15 (B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст