Mitsubishi Galant (2004+). Manual — part 763
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-191
AC305210
CONNECTOR: A-13
AS
A-13 (GR)
AC305977AK
CONNECTOR: B-18X
AC305216
CONNECTOR: B-21 <2.4L>
AB
B-21 (B)
AC305214
B-28 (B)
AC
CONNECTOR: B-28 <2.4L>
AC305229AC
B-21 (B)
CONNECTOR: B-21 <3.8 L>
AC305218
B-28 (B)
AC
CONNECTOR: B-28 <3.8 L>
AC305231
CONNECTOR: C-01
AY
AC305233
CONNECTORS: C-15, C-23
C-15 (B)
C-23
BU
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-192
.
TECHNICAL DESCRIPTION (COMMENT)
If cool air is not distributed when the A/C switch is on,
the A/C compressor relay system may be defective.
.
TROUBLESHOOTING HINTS
• Improper amount of refrigerant
• Malfunction of the air thermo sensor
• Malfunction of the ambient air temperature sen-
sor
• Malfunction of the A/C pressure sensor
• Malfunction of the A/C compressor relay
• Malfunction of the A/C refrigerant temperature
switch
• Malfunction of the air conditioning compressor
clutch
• Malfunction of the A/C-ECU
• Malfunction of the PCM
• Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A (Vehicles with CAN
communication system)
STEP 1. Check the defogger and outside/inside air
selection damper control motor operation.
Q: Do the defogger and outside/inside air selection damper
control motor work normally?
YES : Go to Step 2.
NO : Refer to Inspection procedure 10, "Malfunction of the
A/C-ECU power supply system
STEP 2. Check the blower motor operation.
Q: Does the blower motor work normally?
YES : Go to Step 3.
NO : Refer to Inspection procedure 5, "Front blower fan
and motor do not turn
STEP 3. Check the A/C compressor.
Check the A/C compressor for compressor oil leaks.
Q: Is the check result satisfactory?
YES : Go to Step 4.
NO : Replace the A/C compressor or the expansion valve.
AC305415
CONNECTORS: C-214, C-215
JUNCTION BLOCK
(FRONT VIEW)
C-215
C-214
BB
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-193
STEP 4. Using scan tool MB991958, read the A/C
diagnostic trouble code.
Check if an A/C-ECU DTC is set.
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Check if the DTC is set.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the check result satisfactory?
YES : Go to Step 5.
NO : Refer to DIAGNOSTIC TROUBLE CODE CHART
STEP 5. Check A/C compressor clutch relay connector
B-18X for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is A/C compressor clutch relay connector B-18X in
good condition?
YES : Go to Step 6.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
. Check
that the air conditioning works normally.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305977AJ
CONNECTOR: B-18X
RELAY BOX SIDE
FRONT OF
VEHICLE
JUNCTION BLOCK
TRIANGLE MARK
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-194
STEP 6. Check the A/C compressor clutch relay continuity.
Follow the table below to check the A/C compressor clutch
relay for continuity.
Q: Is the A/C compressor clutch relay in good condition?
YES : Go to Step 7.
NO : Replace the A/C compressor clutch relay. Check that
the air conditioning works normally.
BATTERY
VOLTAGE
TESTER
CONNECTION
SPECIFIED
CONDITION
Not applied
1
− 4
Open circuit
• Connect
terminal 2 to the
positive battery
terminal
• Connect
terminal 3 to the
negative battery
terminal
1
− 4
Less than 2 ohms
AC306655
2
1
3
4
1
2
4
3
AB
A/C COMPRESSOR CLUTCH RELAY
FRONT OF
VEHICLE
JUNCTION BLOCK
TRIANGLE MARK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст