Mitsubishi Galant (2004+). Manual — part 1108
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-125
(4) Measure the voltage between terminal No. 107 and ground.
• Voltage should be between 4.5 and 4.9 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES : Go to Step 6.
NO : Go to Step 7.
AK202956
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
AB
POWER PLANT ECU
CHECK HARNESS CONNECTOR
MB991923
PCM
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
AK203043AB
POWER PLANT ECU
CHECK HARNESS
CONNECTOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-126
STEP 6. Check harness connector B-22 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Repair harness wire between intake air temperature
sensor connector B-10 (terminal No. 1) and PCM
connector B-22 (terminal No. 107) because of open
circuit. Then go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 11.
STEP 7. Check harness connector B-22 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Replace the PCM. Then go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 11.
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-127
STEP 8. Check the continuity at intake air temperature
sensor harness side connector B-10.
(1) Disconnect the connector B-10 and measure at the harness
side.
(2) Check for the continuity between terminal No. 4 and
ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Replace the PCM. Then go to Step 11.
NO : Go to Step 9.
STEP 9. Check harness connector B-21 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 11.
AK303015
2
1
3
4
AB
B-10 (GR)
CONNECTOR: B-10
HARNESS
CONNECTOR:
COMPONENT SIDE
2
1
3
4
AK303019
B-10 HARNESS
CONNECTOR:
COMPONENT SIDE
AB
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-128
STEP 10. Check for open circuit between intake air
temperature sensor connector B-10 (terminal No. 4) and
PCM connector B-21 (terminal No. 69).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 11.
NO : Repair it. Then go to Step 11.
STEP 11. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0113 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AK303015
2
1
3
4
AB
B-10 (GR)
CONNECTOR: B-10
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст