Mitsubishi Galant (2004+). Manual — part 637
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-99
STEP 6. Measure the PCM output voltage to the speed
sensor at the PCM connector B-22 by using check harness
special tool MB991923.
(1) Disconnect all the connectors from the PCM.
(2) Connect special tool MB991923 (check harness) between
the PCM and the body-side harness connector.
(3) Turn the ignition switch to the "ON" position.
AC306248AE
B-22
(B)
CONNECTOR: B-22
PCM
AIR
CLEANER
JAE
94
98
107
103
112
91
100
109
101102
106
110
105
111
97
92
96
93
104
113
108
95
99
AC209793AH
SPECIAL TOOL 23-PIN CONNECTOR
WITH RED TAPE
(PCM CONNECTOR B-22)
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
PCM
MB991923
BODY SIDE
HARNESS
B-22
(GR)
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-100
(4) Measure the voltage between terminal 112 and ground.
• The voltage should measure between 4.5 and 4.9 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES : Go to Step 7.
NO : Go to Step 9.
STEP 7. Check PCM connector B-22 and output shaft
speed sensor connector B-107 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are the connectors in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC210377
JAE
94
98
107
103
112
91
100
109
101
102
106
110
105
111
97
92
96
93
104
113
108
95
99
AC
B-22 HARNESS
CONNECTOR:
COMPONENT SIDE
AC306248AE
B-22
(B)
CONNECTOR: B-22
PCM
AIR
CLEANER
JAE
94
98
107
103
112
91
100
109
101102
106
110
105
111
97
92
96
93
104
113
108
95
99
AC305353AC
CONNECTOR: B-107
BATTERY
B-107 (GR)
3
2
1
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-101
STEP 8. Check the harness for open circuit or damage
between PCM connector B-22 terminal 112 and output
shaft speed sensor connector B-107 terminal 2.
Q: Is the harness wire in good condition?
YES : Go to Step 19.
NO : Repair or replace the harness wire.
AC306248AE
B-22
(B)
CONNECTOR: B-22
PCM
AIR
CLEANER
JAE
94
98
107
103
112
91
100
109
101102
106
110
105
111
97
92
96
93
104
113
108
95
99
AC305353AC
CONNECTOR: B-107
BATTERY
B-107 (GR)
3
2
1
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-102
STEP 9. Check PCM connector B-22 and output shaft
speed sensor connector B-107 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 10.
NO : Repair or replace the damages components. Refer to
GROUP 00E, Harness Connector Inspection
AC306248AE
B-22
(B)
CONNECTOR: B-22
PCM
AIR
CLEANER
JAE
94
98
107
103
112
91
100
109
101102
106
110
105
111
97
92
96
93
104
113
108
95
99
AC305353AC
CONNECTOR: B-107
BATTERY
B-107 (GR)
3
2
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст