Mitsubishi Galant (2004+). Manual — part 1468
HEADLIGHT, FRONT SIDE MARKER LIGHT AND POSITION LIGHT ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-115
Front Turn-signal and Parking Light Bulb
1. Disconnect the front turn-signal light and parking light
connector.
2. Remove the socket with the bulb by turning it
counterclockwise as shown.
CAUTION
Do not touch the surface of the bulb with hands or dirty
gloves as the bulb may fail after a short time. If the surface
does become dirty, clean it with alcohol or thinner, and let
it dry thoroughly before installing.
3. Twist bulb counterclockwise and pull out the bulb from the
socket, and then replace the bulb.
4. Install the socket to the headlight by push and twisting it
clockwise.
Front Side-marker Light Bulb
1. Disconnect the front side-marker light connector.
2. Remove the socket with the bulb by turning it
counterclockwise as shown.
CAUTION
Do not touch the surface of the bulb with hands or dirty
gloves as the bulb may fail after a short time. If the surface
does become dirty, clean it with alcohol or thinner, and let
it dry thoroughly before installing.
3. Pull out the bulb from the socket, and then replace the bulb.
4. Install the socket to the headlight by push and twisting it
clockwise.
BULB REPLACEMENT <PROJECTOR TYPE>
M1542001300711
Headlight Bulb (Low Beam)
1. Disconnect the headlight connector.
2. Remove the headlight bulb by turning it counterclockwise as
shown.
CAUTION
Do not touch the surface of the bulb with hands or dirty
gloves as the bulb may fail after a short time. If the surface
does become dirty, clean it with alcohol or thinner, and let
it dry thoroughly before installing.
3. Install the headlight bulb to the headlight by push and
twisting it clockwise.
AC307146
FRONT TURN-SIGNAL
AND PARKING LIGHT
AB
AC307143
AB
FRONT SIDE-MAKER LIGHT
AC307141
HEADLIGHT (LOW BEAM)
AB
HEADLIGHT, FRONT SIDE MARKER LIGHT AND POSITION LIGHT ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-116
Headlight Bulb (High Beam)
1. When replacing the headlight bulb on the left side, remove
the relay box.
2. Remove the entire socket and bulb assembly by twisting it
counterclockwise as shown.
3. Disconnect the headlight connector.
CAUTION
Do not touch the surface of the bulb with hands or dirty
gloves as the bulb may fail after a short time. If the surface
does become dirty, clean it with alcohol or thinner, and let
it dry thoroughly before installing.
4. Connect the headlight bulb to the headlight connector and
install it to the headlight by push and twisting clockwise.
Front Turn-signal Light and Parking Light Bulb
1. Disconnect the front turn-signal light and parking light
connector.
2. Remove the socket with the bulb by turning it
counterclockwise as shown.
CAUTION
Do not touch the surface of the bulb with hands or dirty
gloves as the bulb may fail after a short time. If the surface
does become dirty, clean it with alcohol or thinner, and let
it dry thoroughly before installing.
3. Pull out the bulb from the socket, and then replace the bulb.
4. Install the socket to the headlight by push and twisting it
clockwise.
Front Side-marker Light Bulb
1. Disconnect the front side-marker light connector.
2. Remove the socket with the bulb by turning it
counterclockwise as shown.
CAUTION
Do not touch the surface of the bulb with hands or dirty
gloves as the bulb may fail after a short time. If the surface
does become dirty, clean it with alcohol or thinner, and let
it dry thoroughly before installing.
3. Pull out the bulb from the socket, and then replace the bulb.
4. Install the socket to the headlight by push and twisting it
clockwise.
AC307142
AB
HEADLIGHT (HIGH BEAM)
AC307139
FRONT TURN-SIGNAL
AND PARKING LIGHT
AB
AC307140
AB
FRONT SIDE-MARKER LIGHT
HEADLIGHT, FRONT SIDE MARKER LIGHT AND POSITION LIGHT ASSEMBLY
TSB Revision
CHASSIS ELECTRICAL
54A-117
HEADLIGHT AND FRONT COMBINATION LIGHT
REMOVAL AND INSTALLATION
M1542002700358
Post-installation operation
• Headlight aiming adjustment (Refer to
).
AC307154
1
4.9 ± 0.7 N·m
44 ± 6 in-lb
4.9 ± 0.7 N·m
44 ± 6 in-lb
1.5 ± 0.2 N·m
14 ± 1 in-lb
AB
HEADLIGHT REMOVAL STEPS
•
RADIATOR GRILL (REFER TO
GROUP 51, RADIATOR GRILL
•
SPLASH SHIELD MOUNTING
CLIPS, FRONT BUMPER UNDER
COVER, RUBBER NUT, LICENSE
PLATE GARNISH (REFER TO
GROUP 51, FRONT BUMPER
<<A>>
1.
HEADLIGHT ASSEMBLY
HEADLIGHT REMOVAL STEPS
FOG LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-118
REMOVAL SERVICE POINT
.
<<A>> HEADLAIGHT ASSEMBLY REMOVAL
Remove the front bumper mounting screw and clip.
FOG LIGHT
FOG LIGHT DIAGNOSIS
M1542000701366
The fog lights are controlled by the Simplified Wiring
System (SWS). For troubleshooting, refer to GROUP
54B, SWS Diagnosis
ON-VEHICLE SERVICE
FOG LIGHT AIMING
M1542001100472
PRE-AIMING INSTRUCTIONS
1. Inspect for badly rusted or faulty fog light assemblies.
2. These conditions must be corrected before a satisfactory
adjustment can be made.
3. Inspect tire inflation, and adjust if necessary.
4. If the fuel tank is not full, place a weight in the trunk of the
vehicle to simulate weight of a full tank [3 kg (6.5 pounds)
per gallon].
5. There should be no other load in the vehicle other than
driver or substituted weight of approximately 70 kg (150
pounds) placed in driver's position.
6. Thoroughly clean the fog light lenses.
7. Place the vehicle on a level floor, perpendicular to a flat
screen 7.62 meters (25.0 feet) away from the bulb
center-marks on the foglight lens.
8. Rock the vehicle sideways to allow the vehicle to assume its
normal position.
9. Bounce the front suspension through three (3) oscillations
by applying the body weight to the hood or bumper.
AC307557
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст