Mitsubishi Galant (2004+). Manual — part 191
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-55
SYMPTOM CHART
M1172002300366
SYMPTOM
INSPECTION
PROCEDURE NO.
REFERENCE
PAGE
Communication with
scan tool is not
possible
Communication with all systems is
impossible
-
Group 13A,
Symptom
Procedures
−
Inspection
Procedure 1
<2.4L
engine>.
Group 13B,
Symptom
Procedures
−
Inspection
Procedure 1
<3.8L
engine>.
Communication with the PCM only is
impossible
-
Group 13A,
Symptom
Procedures
−
Inspection
Procedure 2
<2.4L
engine>.
Group 13B,
Symptom
Procedures
−
Inspection
Procedure 2
<3.8L
engine>.
Auto-cruise control
is not cancelled.
When brake pedal is depressed
1
When selector lever is moved to "N" range 2
When "CANCEL" switch is turned ON
3
Auto-cruise control cannot be set.
4
Hunting (repeated acceleration and deceleration) occurs at the
set vehicle speed.
5
When "CRUISE" (MAIN) switch is turned "ON", "CRUISE"
indicator light inside combination meter does not illuminate.
(However, Auto-cruise Control is Normal).
6
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-56
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: When the Brake Pedal is Depressed, Auto-cruise Control is not
Cancelled.
.
COMMENT
The stoplight switch circuit is suspected.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case:)
• Malfunction of the stoplight switch.
• Damaged harness or connector.
• Malfunction of the PCM.
DIAGNOSIS
Refer to
, Diagnostic Trouble Code Procedures
− DTC
22: Stoplight Switch System.
INSPECTION PROCEDURE 2: When the Selector Lever is Moved to "N" Range, Auto-cruise Control is
not Cancelled.
.
COMMENT
The transmission range switch circuit is suspected.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case:)
• Malfunction of the transmission range switch.
• Damaged harness or connector.
• Malfunction of the PCM.
DIAGNOSIS
Refer to GROUP 23A, Diagnostic Trouble Code Procedures
−
DTC 27: Transmission Range Switch System (Open Circuit)
, DTC 28: Transmission Range Switch System
.
INSPECTION PROCEDURE 3: When the Auto-cruise Control "CANCEL" Switch is Set to ON,
Auto-cruise Control is not Cancelled.
.
COMMENT
The cause is probably an open-circuit in the output in
the circuit inside the "CANCEL" switch.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case:)
• Malfunction of the auto-cruise control switch.
DIAGNOSIS
Replace the auto-cruise control switch. (Refer to
Auto-cruise Control).
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-57
INSPECTION PROCEDURE 4: Auto-cruise Control cannot be Set.
.
COMMENT
The fail-safe function is probably canceling
auto-cruise control. In this case, scan tool MB991958
can be used to retest each system by checking the
diagnostic trouble codes. The scan tool can also be
used to check if the circuits of each input switch are
normal or not by checking the input switch codes.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case:)
• Malfunction of the auto-cruise control switch.
• Malfunction of the stoplight switch.
• Malfunction of the transmission range switch.
• Malfunction of the PCM.
DIAGNOSIS
Required Special Tool:
• MB991958: Scan tool (MUT-III sub assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB cable
• MB991910: MUT-III main harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector
(2) Turn the ignition switch to the "ON" position.
(3) Check for auto-cruise control system diagnostic trouble
code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is DTC set?
YES : Refer to
, Diagnostic Trouble Code Chart.
Then go to Step 6 .
NO : Go to Step 2 .
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-58
STEP 2. Using scan tool MB991958, check data list item 04:
Cancel Switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to data reading mode.
• Auto-cruise control system item 04, Cancel Switch.
• When "CANCEL" switch is at the ON position, the
display on scan tool MB991958 should be "ON".
• When "CANCEL" switch is at the OFF position, the
display on scan tool MB991958 should be "OFF".
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is the switch operating properly?
YES : Go to Step 3 .
NO : Refer to
, Symptom Procedures number 3.
Then go to Step 6 .
STEP 3. Using scan tool MB991958, check data list item 05:
Stoplight Switch and data list item 06: Brake switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to data reading mode.
• Auto-cruise control system item 05, Stoplight Switch.
• When brake pedal is depressed, the display on scan
tool MB991958 should be "ON".
• When brake pedal is released, the display on scan
tool MB991958 should be "OFF".
(4) Set scan tool MB991958 to data reading mode.
• Auto-cruise control system item 06, Brake Switch.
• When brake pedal is depressed, the display on scan
tool MB991958 should be "ON".
• When brake pedal is released, the display on scan
tool MB991958 should be "OFF".
(5) Turn the ignition switch to the "LOCK" (OFF) position.
(6) Disconnect scan tool MB991958.
Q: Is the switch operating properly?
YES : Go to Step 4 .
NO : Refer to
, Symptom Procedures number 1.
Then go to Step 6 .
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст