Mitsubishi Galant (2004+). Manual — part 8
THEFT PROTECTION
TSB Revision
BODY CONSTRUCTION
1-29
LOCATIONS
LABEL AREA (A: FOR ORIGINAL EQUIPMENT PARTS, B: FOR REPLACEMENT PARTS)
AC000058
ENGINE
<2.4L ENGINE>
AD
A
B
AC000061
ENGINE
<3.8L ENGINE>
AC
B
A
AC000060
AUTOMATIC TRANSAXLE
AB
A
B
AC307026AB
A
B
HOOD
AC307027
A
B
FENDER
THE ILLUSTRATION INDICATES
LEFT OUTER SIDE.
RIGHT SIDE IS SYMMETRICALLY
OPPOSITE.
AB
AC307028AB
A
B
REAR QUARTER OUTER PANEL
THE ILLUSTRATION INDICATES LEFT OUTER SIDE.
RIGHT SIDE IS SYMMETRICALLY OPPOSITE.
THEFT PROTECTION
TSB Revision
BODY CONSTRUCTION
1-30
LABEL AREA (A: FOR ORIGINAL EQUIPMENT PARTS, B: FOR REPLACEMENT PARTS)
AC307042AB
A
B
FRONT DOOR
THE ILLUSTRATION INDICATES LEFT INNER SIDE.
RIGHT SIDE IS SYMMETRICALLY OPPOSITE.
C
C
SECTION C-C
AC307044AB
A
B
REAR DOOR
THE ILLUSTRATION INDICATES LEFT INNER SIDE.
RIGHT SIDE IS SYMMETRICALLY OPPOSITE.
D
D
SECTION D-D
AC307046AB
A
B
TRUNK LID
AC307067AB
B
A
FRONT BUMPER
AC307083AB
A
B
REAR BUMPER
2-1
GROUP 2
BODY DIMENSIONS
CONTENTS
BODY DIMENSIONS AND
MEASUREMENT METHODS. . . . . . .
TYPE A (PROJECTED DIMENSIONS)
UNDER BODY . . . . . . . . . . . . . . . . . . . . . .
SUSPENSION INSTALLATION DIMENSIONS
TYPE B (ACTUAL-MEASUREMENT
DIMENSIONS). . . . . . . . . . . . . . . . . . .
UNDER BODY. . . . . . . . . . . . . . . . . . . . . . .
SUSPENSION INSTALLATION
DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . .
FRONT BODY . . . . . . . . . . . . . . . . . . . . . . .
SIDE BODY . . . . . . . . . . . . . . . . . . . . . . . . .
REAR BODY . . . . . . . . . . . . . . . . . . . . . . . .
INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . .
BODY DIMENSIONS AND MEASUREMENT METHODS
TSB Revision
BODY DIMENSIONS
2-2
BODY DIMENSIONS AND MEASUREMENT METHODS
M4020001000158
1. Type A (projected dimensions)
Indicates the dimension when a measurement location is
projected onto the plane.
The difference in height of the measurement points should
be taken into consideration when measuring.
2. Type B (actual-measurement dimensions)
Indicates the actual distance between the measurement
points.
Measure using a tracking gauge or a measuring tape, etc.
NOTE:
.
•
Make the lengths of the tracking gauge probes the same
(A=A’).
•
Do not bend or twist the measuring tape.
3. Insert the tracking gauge probes securely into the
measurement holes.
4. When the standard dimensions in the illustration are
enclosed by oblong, this indicates that the symmetrical left
and right positions have the same dimensions.
5. When using a notch for dimension measurement, set the
measuring point at the center of the notch.
AB100778
PROJECTED DIMENSION
HEIGHT
PROBE
AB
AB100779AB
ACTU
ALL
Y-MEASURED
DIMENSION
A
A'
AB100780
AB100780AB
CENTER OF HOLE
AB100781AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст