Mitsubishi Galant (2004+). Manual — part 853
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-229
STEP 5. Check the cylinder 1, 4 heated oxygen sensor
(front).
(1) Disconnect the cylinder 1, 4 heated oxygen sensor (front)
connector B-37 and connect test harness special tool
MB991316 to the connector on the cylinder 1, 4 heated
oxygen sensor (front) side.
(2) Warm up the engine until engine coolant temperature
reaches 80
°C (176°F) or higher.
(3) Perform a racing for 5 minutes or more with the engine
speed of 4,500 r/min.
(4) Connect a digital voltage meter between terminal No. 2
(black clip) and terminal No. 4 (white clip).
(5) While repeatedly revving the engine, measure the cylinder
1, 4 heated oxygen sensor (front) output voltage.
Standard value: 0.6
− 1.0 volt
CAUTION
• Be very careful when connecting the jumper wires;
incorrect connection can damage the heated oxygen
sensor (front).
• Be careful the heater is broken when voltage of beyond
8 volts is applied to the heated oxygen sensor (front)
heater.
NOTE: If the sufficiently high temperature [of approximate
400
°
C (752
°
F) or more] is not reached although the heated
oxygen sensor (front) is normal, the output voltage would be
possibly low although the rich air/fuel ratio. Therefore, if the
output voltage is low, use a jumper wire to connect the ter-
minal No. 1 (red clip) and the terminal No. 3 (blue clip) of
the heated oxygen sensor (front) with the positive terminal
and the negative terminal of 8 volts power supply respec-
tively, then check again.
Q: Is the measured voltage between 0.6 and 1.0 volt?
YES : Go to Step 6.
NO : Replace the cylinder 1, 4 heated oxygen sensor
(front). Then go to Step 11.
AK303821
1
2
3
4
AB
CONNECTOR: B-37
CYLINDER 1, 4
HEATED OXYGEN
SENSOR (FRONT)
B-37 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AKX01624
HEATED
OXYGEN
SENSOR
COMPONENT
SIDE
CONNECTOR
MB991316
WHITE
BLACK
AN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-230
STEP 6. Check harness connector B-01, B-27 at injector for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 11.
STEP 7. Check the cylinder 1, 4 injector.
(1) Disconnect each injector connector.
(2) Measure the resistance between injector side connector
terminal No. 1 and No. 2.
Standard value: 10.5
− 13.5 ohms [at 20°C (68°F)]
Q: Is the measured resistance between 10.5 and 13.5 ohms
[at 20
°C (68°F)]?
YES : Go to Step 8.
NO : Replace the injector. Then go to Step 11.
M
1
2
AK303822
B-01 (GR)
B-27 (GR)
CONNECTORS: B-01, B-27
AB
HARNESS CONNECTOR:
COMPONENT SIDE
M
1
2
AK303822
B-01 (GR)
B-27 (GR)
CONNECTORS: B-01, B-27
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK000559
2
1
INJECTOR SIDE
CONNECTOR
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-231
STEP 8. Check harness connector B-22, B-23 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 11.
AK303057
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
CONNECTORS: B-22, B-23
B-22 (B)
AB
B-23
B-22 HARNESS CONNECTOR:
COMPONENT SIDE
B-23 HARNESS CONNECTOR:
COMPONENT SIDE
PCM
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-232
STEP 9. Check for harness damage between cylinder 1, 4
heated oxygen sensor (front) connector B-37 (terminal No.
4) and PCM connector B-22 (terminal No. 92).
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair it. Then go to Step 11.
AK303821
1
2
3
4
AB
CONNECTOR: B-37
CYLINDER 1, 4
HEATED OXYGEN
SENSOR (FRONT)
B-37 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст