Mitsubishi Galant (2004+). Manual — part 838
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-169
DIAGNOSIS
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
• MB991658: Test Harness
STEP 1. Using scan tool MB991958, check data list item 79:
Throttle Position Sensor (main).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Detach the intake air hose at the throttle body.
(4) Disconnect the connector of the throttle position sensor.
(5) Use test harness special tool (MB991658) to connect only
terminals No. 3, No. 4, No. 5, and No. 6.
(6) Set scan tool MB991958 to the data reading mode for item
79, Throttle Position Sensor (main).
• Output voltage should be between 0.3 and 0.7 volt when
the throttle valve is fully closed with your finger.
• Output voltage should be 4.0 volts or more when the
throttle valve is fully open with your finger.
(7) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Go to Step 2.
STEP 2. Check harness connector B-06 at throttle position
sensor for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 8.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-170
STEP 3. Check the continuity at throttle position sensor
harness side connector B-06.
(1) Disconnect the connector B-06 and measure at the harness
side.
(2) Measure the continuity between terminal No. 3 and ground
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 7.
NO : Go to Step 4.
STEP 4. Check harness connector B-22 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 8.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
1
6 5 4 3 2
AK203051
B-06 HARNESS
CONNECTOR:
COMPONENT SIDE
AC
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-171
STEP 5. Check for open circuit and harness damage
between throttle position sensor connector B-06 (terminal
No. 3) and PCM connector B-22 (terminal No. 95).
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it. Then go to Step 8.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-172
STEP 6. Using scan tool MB991958, check data list item 79:
Throttle Position Sensor (main).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Detach the intake air hose at the throttle body.
(4) Disconnect the connector of the throttle position sensor.
(5) Use test harness special tool (MB991658) to connect only
terminals No. 3, No. 4, No. 5, and No. 6.
(6) Set scan tool MB991958 to the data reading mode for item
79, Throttle Position Sensor (main).
• Output voltage should be between 0.3 and 0.7 volt when
the throttle valve is fully closed with your finger.
• Output voltage should be 4.0 volts or more when the
throttle valve is fully open with your finger.
(7) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Replace the PCM. Then go to Step 8.
STEP 7. Replace the throttle body assembly.
(1) Replace the throttle body assembly.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P0123 set?
YES : Replace the PCM. Then go to Step 8.
NO : The procedure is complete.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст