Mitsubishi Galant (2004+). Manual — part 1365
RADIATOR GRILLE
TSB Revision
EXTERIOR
51-5
RADIATOR GRILLE
REMOVAL AND INSTALLATION
M1511002900237
AC306184
AB
SECTION B – B
SECTION A – A
CLIP
CLIP
RADIATOR GRILLE
RADIATOR GRILLE
RADIATOR GRILLE
FRONT BUMPER
FRONT END
UPPER BAR
B
B
A
A
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-6
GARNISHES AND MOLDINGS
SPECIAL TOOLS
M1511000601158
MOLDINGS
REMOVAL AND INSTALLATION
M1511004700165
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990784 Ornament
remover
General service tool
Side protector moulding
Roof drip molding
MB990784
AC306486
AB
2
4
3
1
A
A
A
A
B
B
AB
AC306021
AC306022
AC307267 AB
SECTION A – A
SECTION B – B
3
1, 2
CLIP
DOOR OUTER
PANEL
FRONT FENDER
SIDE OUTER PANEL
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-7
Required Special Tools:
• MB990784: Ornament Remover
ADHESIVE TAPE POSITION
REMOVAL
<<A>> >>A<<
1. FRONT DOOR SIDE PROTECTOR
MOULDING
<<A>> >>A<<
2. REAR DOOR SIDE PROTECTOR
MOULDING
ROOF DRIP MOULDING REMOVAL
STEPS
<<A>> >>A<<
3. ROOF DRIP MOULDING
FRONT DELTA GARNISH REMOVAL
STEPS
4. FRONT DELTA GARNISH
AC306520 AB
ADHESIVE TAPE: DOUBLE-SIDED TAPE
A: 10.0 mm ( 0.39 in ) WIDTH AND 1.52 mm ( 0.06 in ) THICKNESS,
B: 8.0 mm ( 0.32 in ) WIDTH AND 1.2 mm ( 0.05 in ) THICKNESS
FRONT DOOR SIDE PROTECTOR MOULDING
REAR DOOR SIDE PROTECTOR MOULDING
ROOF DRIP MOULDING
B
B
A
36.5 ± 1 mm
(1.44 ± 0.04 inch)
29 ± 1 mm
(1.14 ± 0.04 inch)
5.5 ± 0.5 mm
(0.22 ± 0.02 inch)
6.4 ± 0.5 mm
(0.25 ± 0.02 inch)
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-8
REMOVAL SERVICE POINTS
.
<<A>> SIDE PROTECTOR MOULDING/ROOF DRIP MOUL-
DING REMOVAL
Gently lift and remove the side protector moulding/roof drip
moulding. If there is any double-sided tape remaining on the
side protector moulding, remove according to the following
instructions.
<Remove double-sided tape remaining on the body sur-
face>
1. Attach protection tape all the way along the edges of the
double-sided tape which is still adhering to the body.
2. Scrape off the double-sided tape with a resin spatula as
much as possible.
3. Peel off the protection tape.
4. Use a shop towel moistened with 3M
AAD Part number
8906 or equivalent to wipe the body.
.
<Remove double-sided tape remaining on SIDE PROTEC-
TOR MOULDING/ROOF DRIP MOULDING and adhere dou-
ble-sided tape (when re-using SIDE PROTECTOR
MOULDING/ROOF DRIP MOULDING)>
1. Scrape off the double-sided tape on the side protector
moulding with a resin spatula as much as possible.
2. Use a shop towel moistened with 3M
AAD Part number
8906 or equivalent to wipe the side protector moulding
surface.
3. Remove only a small portion of the residual adhesive.
4. Apply primer to adherence area of the side protector
moulding, then adhere the double-sided tape as specified on
the side protector moulding (Refer to double-sided tape
adherence location ).
AC000420
DOUBLE-SIDED TAPE
PROTECTION TAPE
AB
AC000421
DOUBLE-SIDED TAPE
AB
AC000422
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст