Mitsubishi Galant (2004+). Manual — part 1492
RADIO WITH CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-211
STEP 5. Check again using a normal CD, which is not dirty
or scratched.
• Load another normal CD.
• Check that the CD player recognizes and play the CD.
Q: When you substitute another normal CD, is the CD
loaded correctly?
YES : The original CD is defective. Check that a CD can be
inserted.
NO : Replace or repair the CD player. Check that a CD can
be inserted.
INSPECTION PROCEDURE 24: No Sound (CD Only).
DIAGNOSIS
STEP 1. Check again using another CD, which is not dirty
or scratched.
Q: When you substitute another normal CD, is the CD
played normally?
YES : The original CD is defective. The CD player should
sound normally.
NO : Go to Step 2.
STEP 2. Check power supply to the CD player when the
ignition switch is at "ACC" or "ON" position.
Q: Is the radio and CD player energized when the ignition
switch is turned to the "ACC" or "ON" position?
YES : Replace the radio and CD player or radio, CD player
and CD changer. The CD player should sound
normally.
NO : Check the memory backup power supply circuit.
Refer to Inspection Procedure 1
RADIO WITH CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-212
INSPECTION PROCEDURE 25: CD Sound Skips.
DIAGNOSIS
STEP 1. Check the state in which the sound on the CD
jumps.
Q: Does the sound jump when the car is parked?
YES : Go to Step 2.
NO : Go to Step 4.
STEP 2. Check the surface of the CD.
Q: Are there any scratches or soiling on the CD?
YES : The CD is defective if there are any scratches. Clean
the CD surface if it is dirty. Check that a CD sound
skip is resolved.
NO : Go to Step 3.
STEP 3. Check when replacing with a CD that can be
played normally without any scratches or soiling.
Q: Does the CD play normally when replaced with a CD that
is not scratched or dirty and can play normally?
YES : Defective CD used. Check that a CD sound skip is
resolved.
NO : Go to Step 4.
STEP 4. Check by tapping the radio and CD player or radio,
CD player and CD changer.
NOTE: Check by using a known-good CD which is free from
scratches, dirt or any other abnormality.
Q: Does the sound jump when tapping the radio and CD
player or radio, CD player and CD changer?
YES : Securely mount the radio and CD player or radio, CD
player and CD changer. Check that a CD sound skip
is resolved.
NO : Either replace the audio system or take the following
measures if a servicing shop is nearby.
1. Investigate in detail the conditions when the
sound jumps while driving the car.
2. Describe these conditions to the service shop
for consultation.
3. Either replace the radio and CD player or
radio, CD player and CD changer according to
the instructions of the service shop.
Check that a CD sound skip is resolved.
RADIO WITH CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-213
INSPECTION PROCEDURE 26: Sound Quality is Poor.
DIAGNOSIS
Check to see that the CD can be played normally and that it
is free of any scratches or soiling.
Replace with better sound quality CD.
Q: Is the sound quality better replacing the CD with a clean
CD without any scratches that can be played?
YES : The CD is defective. The sound quality should return
to normal.
NO : Replace the audio. The sound quality should return to
normal.
INSPECTION PROCEDURE 27: CD cannot be Ejected.
DIAGNOSIS
Check the power of ignition switch "ACC".
Q: Does the radio and CD player or radio, CD player and
CD changer power turn ON when the ignition switch is
in the "ACC" or "ON" position?
YES : Either replace the radio and CD player or radio, CD
player and CD changer. Check that a CD can be
ejected normally.
NO : Check the memory backup power supply circuit.
Refer to Inspection Procedure 1
RADIO WITH CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-214
ON-VEHICLE SERVICE
SPEAKER TEST (Vehicles with seven speakers)
M1544005400318
Operate the radio panel switches to test the speakers. The
multi-center display (middle grade type) shows which speaker
is sounding. Enter the speaker test mode according to the fol-
lowing steps:
1. Turn the ignition switch to "ACC" position and switch off the
audio.
2. Press the following buttons in that order within 60 seconds
from step (1).
(1) Memory select "1" button
(2) "SEEK" switch (down side)
(3) "SEEK" switch (up side)
(4) Memory select "6" button
3. Check that the speaker, which is displayed on the
multi-center display (middle grade type), sounds (If the
memory select "6" button is pressed, the speaker will be
changed).
4. If a button other than the memory select "6" button and
"EJECT" button (CD) is pressed, or the ignition switch is
turned to "LOCK" (OFF) position, you will exit from the
speaker test mode.
6
READY
SCAN
RPT RDM
C D
SEEK
TRACK
LOAD EJECT
5
4
3
2
1
FM AM
VO
L /
PUSH
PW
R
T
U
NE
/
PUSH
AUD
IO
AC208556
MEMORY SELECT BUTTON (1. 6)
SEEK (DOWN)
SWITCH
AB
SEEK (UP)
SWITCH
AC208718 AB
FRONT SPEAKER (LH)
CHECK PROCESSING
FRONT (LH)
REAR (LH)
REAR (RH)
FRONT (RH)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст