Mitsubishi Galant (2004+). Manual — part 343
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-563
INSPECTION PROCEDURE N-8: Transmitter: ETACS-ECU does not receive any signal from the lock,
unlock, trunk or panic switch.
.
CIRCUIT OPERATION
The ETACS-ECU receives signal through its receiver
from the transmitter, and operates the keyless entry
system according to the signal.
.
TECHNICAL DESCRIPTION (COMMENT)
If the signal is not normal, the keyless entry transmit-
ter does not work normally.
.
TROUBLESHOOTING HINTS
• The transmitter may be defective
• The ETACS-ECU may be defective
DIAGNOSIS
Required Special Tool:
• MB991223: Harness Set
STEP 1. Register the transmitter.
Register the transmitter. Refer to GROUP 42, Keyless Entry
System, On-vehicle Service, How to register secret code
.
Q: Can the transmitter be registered correctly?
YES : If the transmitter works normally, the input signal from
the transmitter should be normal.
NO : Go to Step 2.
STEP 2. Check the transmitter battery.
Measure the voltage of the transmitter battery.
• The value should be approximately 2.5 - 3.2 volts.
Q: Is the measured voltage approximately 2.5 - 3.2 volts
(battery positive voltage)?
YES : Go to Step 3.
NO : Replace the battery. If the transmitter can be
registered normally, and operates normally, it
indicates that the transmitter is sending normal signal
to the ECU.
AC002099AB
Reciver and Transmitter Communication Circuit
ACX01609
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-564
STEP 3. Check the transmitter.
Replace the transmitter and register the code. Refer to GROUP
42, Keyless Entry System, On-vehicle Service, How to register
secret code
Q: Can the transmitter be registered correctly?
YES : If the transmitter works normally, the input signal from
the transmitter should be normal.
NO : Replace the ETACS-ECU. If the transmitter works
normally, the input signal from the transmitter should
be normal.
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-565
INSPECTION PROCEDURE N-9: ETACS-ECU does not receive any interior light loaded signal.
IGNITION
SWITCH (ACC)
IGNITION
SWITCH (IG1)
BATTERY
RELAY
BOX
JOINT
CONNECTOR (1)
JUNCTION BLOCK
ETACS-ECU
LOAD
DETERMINATION
CIRCUIT
POWER
SOURCE
INTERIOR LIGHT CUT BACK-UP
CIRCUIT
KEEP RELAY
·MAP LIGHT ASSEMBLY
<WITHOUT SUNROOF>
·OVER HEAD CONSOLE
<WITH SUNROOF>
·REAR DOME LIGHT
JUNCTION BLOCK SIDE
Interior Light Automatic Shut-Down Function Circuit
INPUT SIGNAL PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-566
.
CIRCUIT OPERATION
The ETACS-ECU operates the following equipment
or functions by the interior light loaded signal:
• Interior light automatic shut-down function
• Dome light
• Ignition key hole illumination light
.
TECHNICAL DESCRIPTION (COMMENT)
If the signal is not normal, the equipment or functions
described in "CIRCUIT OPERATION" do not work
normally.
.
TROUBLESHOOTING HINTS
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
• The ETACS-ECU may be defective
AC305231
CONNECTOR: C-01
AY
AC305415AS
CONNECTORS: C-214, C-215
C-214
C-215
AC305413AB
CONNECTOR: C-219
JUNCTION BLOCK
(REAR VIEW)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст