Mitsubishi Galant (2004+). Manual — part 244
![](/vehicles/winoney/jucether/peds/rutrndic.png)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-167
INSPECTION PROCEDURE C-4: Central Door Locking System: All the Doors do not Lock or Unlock
with just the Door Lock Key Cylinder Key Operation.
.
TECHNICAL DESCRIPTION (COMMENT)
The door lock key cylinder switch or the ETACS-ECU
may be defective.
.
TROUBLESHOOTING HINTS
• Trouble in input signal system
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
• The ETACS-ECU may be defective
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
DOOR LOCK
ACTUATOR
INPUT SIGNAL
DOOR LOCK KEY CYLINDER SWITCH
FUSIBLE
LINK
1
JUNCTION BLOCK SIDE
JUNCTION BLOCK
ETACS-ECU
Central Door Lock (Door Lock Key Cylinder Switch) Circuit
![](/vehicles/winoney/jucether/peds/kig.png)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-168
Check the input signal (by using the pulse check mode of
the monitor).
Check the input signals from the door lock key cylinder switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect the special tool. Refer to "How to connect SWS
monitor
."
(2) When the doors are locked and unlocked by using the
driver's or front passenger's door lock key cylinder, check
that scan tool MB991958 sounds.
(3) Operate scan tool MB991958 according to the procedure
below to display "Pulse check."
a. Select "Interactive Diagnosis."
b. Select "System Select."
c. Select "SWS."
d. Select "Pulse Checking."
Q: When the doors are locked and unlocked by using the
driver's or front passenger's door lock key cylinder,
does scan tool MB991958 sound?
YES : Replace the ETACS-ECU. Check that all the doors
should be locked and unlocked by using each door
lock key cylinder switch.
NO : Refer to Inspection Procedure N-4 "ETACS-ECU
does not receive any signal from the door lock key
cylinder switch
."
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
![](/vehicles/winoney/jucether/peds/lowanggo.png)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-169
INSPECTION PROCEDURE C-5: Central Door Locking System: All the Doors do not Lock or Unlock
with just the Driver's or Front Passenger's inside Lock Knob Operation.
.
TECHNICAL DESCRIPTION
The door lock actuator or the ETACS-ECU may be
defective.
.
TROUBLESHOOTING HINTS
• Trouble in input signal system
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
• The ETACS-ECU may be defective
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
DOOR LOCK
ACTUATOR
INPUT SIGNAL
·FRONT DOOR LOCK ACTUATOR (LH)
FUSIBLE
LINK
1
JUNCTION BLOCK SIDE
JUNCTION BLOCK
ETACS-ECU
·FRONT DOOR LOCK ACTUATOR (RH)
Central Door Lock (Door Lock Key Cylinder Switch) Circuit
![](/vehicles/winoney/jucether/peds/myove.png)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-170
Check the input signal (by using the pulse check mode of
the monitor).
Check the input signals from the driver's or front passenger's
door lock actuator.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect the special tool. Refer to "How to connect SWS
monitor
."
(2) When the driver's inside lock knob is locked or unlocked,
check if scan tool MB991958 sounds or not.
(3) Operate scan tool MB991958 according to the procedure
below to display "Pulse check."
a. Select "Interactive Diagnosis."
b. Select "System Select."
c. Select "SWS."
d. Select "Pulse Checking."
Q: Does scan tool MB991958 sound when the driver's or
the front passenger's inside lock knob is moved from
"LOCK" to "UNLOCK" or vice versa?
YES : Replace the ETACS-ECU. Check that all the doors
can be locked or unlocked by operating the driver's
inside lock knob.
NO : Refer to Inspection Procedure N-5 "ETACS-ECU
does not receive any signal from the front or rear door
lock actuator
."
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст