Mitsubishi Montero (1991+). Manual — part 198
of part with damaged threads if
available; otherwise, replace
bushing.
Attaching hardware
threads stripped
(threads missing) . .. A . . Require replacement of part
with stripped threads if
available; otherwise, replace
bushing.
Binding . . . . . A .. Require repair or replacement.
Deteriorated, affecting
performance . . . A .. Require repair or replacement.
Distorted, affecting
performance . . . A .. Require repair or replacement.
Leaking (fluid-filled
type) . . . . .. A . . . Require replacement.
Missing . . . . . C . . . Require replacement.
Noisy . . . . ... 2 . . .. ( 1) Further inspection
required.
Rubber separating from
internal metal sleeve on
bonded bushing . . . A . . . Require replacement.
Seized . . . . .. A . . . Require replacement.
Shifted (out of
position) . . . .. B .. Require repair or replacement.
Split . . . . ... A . . . Require replacement.
Surface cracking (weather-
checked) . . . ... .. . . No service suggested or
required.
(1) - If noise isolated to bushing, suggest repair or
replacement.
CAUTION: Use only approved lubricant on rubber bushings.
Petroleum-based lubricants may damage rubber bushings.
CENTER LINKS
CENTER LINK INSPECTION
Condition Code Procedure
Attaching hardware
incorrect . . . .. A . . .. Require replacement of
incorrect part, if available;
otherwise, replace center link.
Attaching hardware
loose . . . . .. A ... Require repair or replacement
of loose part, if available;
otherwise, replace center link.
Attaching hardware
missing . . . . C .. Require replacement of missing
part, if available; otherwise,
replace center link.
Attaching hardware
threads damaged . . A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace center link.
Attaching hardware
threads stripped
(threads missing) . .. A . . Require replacement of part
with stripped threads, if
available; otherwise, replace
center link.
Bent . . . . . B . . . Require replacement.
Binding . . . . . A . . ... ( 1) Further inspection
required.
Grease boot cracked . . 2 . . (2) Suggest replacement.
Grease boot missing . . 2 . . (3) Suggest replacement.
Grease boot torn . . 2 . . (4) Suggest replacement.
Grease fitting broken ... A ... Require replacement of grease
fitting.
Grease fitting missing .. C ... Require replacement of grease
fitting.
Grease fitting
won’t seal . . . . A ... Require replacement of grease
fitting.
Grease seal missing . . 2 . . (3) Suggest replacement.
Grease seal torn . . 2 . . (4) Suggest replacement.
Looseness (perceptible
horizontal movement) ... 1 . . (5) Suggest replacement.
Looseness that is
excessive . . . .. B . . (5)(6) Require replacement.
Seized . . . . .. A . . . Require replacement.
Stud bent . . . ... B . . (7) Require replacement.
Stud broken . . . . A . . (7) Require replacement.
Stud loose in
taper hole . . . . A . . ... ( 7) Require repair or
replacement.
Taper hole elongated . A . . (8) Require replacement.
Threads damaged . . . A .. Require repair or replacement.
Threads stripped
(threads missing) . .. A . . (7) Require replacement.
Wear exceeds
manufacturer’s
specifications . . . B . . . Require replacement.
(1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
(2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
(3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
(4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
(5) - If manufacturer’s procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and socket
movement. Use only moderate hand pressure.
(6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
(7) - Check for damaged taper hole.
(8) - Check for damaged stud.
CONTROL ARM SHAFTS
CONTROL ARM SHAFT INSPECTION
Condition Code Procedure
Attaching hardware
broken . . . . . A ... Require replacement of broken
part, if available; otherwise,
replace shaft.
Attaching hardware
loose . . . . .. A ... Require repair or replacement
of loose part, if available;
otherwise, replace shaft.
Attaching hardware
missing . . . . C .. Require replacement of missing
part, if available; otherwise,
replace shaft.
Attaching hardware
threads damaged . . A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace shaft.
Attaching hardware
threads stripped
(threads missing) . .. A . . Require replacement of part
with stripped threads, if
available; otherwise, replace
shaft.
Bent . . . . . B . . . Require replacement.
Shaft bushing surface
undersized (worn) . .. B . . . Require replacement.
Threads damaged . . . A .. Require repair or replacement.
Threads stripped (threads
missing) . . . ... A . . . Require replacement.
CONTROL ARMS
CONTROL ARM INSPECTION
Condition Code Procedure
Attaching hardware
bent . . . . ... B ... Require repair or replacement
of bent part, if available;
otherwise, replace control arm.
Attaching hardware
broken . . . . . A ... Require replacement of broken
part, if available; otherwise,
replace control arm.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part, if available; otherwise,
replace control arm.
Attaching hardware
incorrect . . . .. A . . .. Require replacement of
incorrect part, if available;
otherwise, replace control arm.
Attaching hardware
loose . . . . .. A ... Require repair or replacement
of loose part, if available;
otherwise, replace control arm.
Attaching hardware
missing . . . . C .. Require replacement of missing
part, if available; otherwise,
replace control arm.
Attaching hardware
threads damaged . . A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace control arm.
Attaching hardware
threads stripped
(threads missing) . .. A . . Require replacement of part
with stripped threads, if
available; otherwise, replace
control arm.
Bent . . . . . B . . . Require replacement.
Bushing hole oversized .. B . . . Require replacement.
Ball joint hole oversized
(loose interference or
press fit) . . . . B . . .. ( 1) Further inspection
required.
Corroded, affecting
structural integrity ... A . . . Require replacement.
Holes distorted . . . A . . . Require replacement.
Threads damaged . . . A .. Require repair or replacement.
Threads stripped (threads
missing) . . . ... A . . . Require replacement.
(1) - If oversized ball joint is available, require
replacement of ball joint. If oversized ball joint
is not available, require replacement of control arm.
DRAG LINKS
DRAG LINK INSPECTION
Condition Code Procedure
Attaching hardware
incorrect . . . .. A . . .. Require replacement of
incorrect part, if available;
otherwise, replace drag link.
Attaching hardware
loose . . . . .. A ... Require repair or replacement
of loose part, if available;
otherwise, replace drag link.
Attaching hardware
missing . . . . C .. Require replacement of missing
part, if available; otherwise,
replace drag link.
Attaching hardware
threads damaged . . A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace drag link.
Attaching hardware
threads stripped
(threads missing) . .. A . . Require replacement of part
with stripped threads, if
available; otherwise, replace
drag link.
Bent . . . . . B . . . Require replacement.
Binding . . . . . A . . .. ( 1) Further inspection
required.
Grease boot cracked . . 2 . . (2) Suggest replacement.
Grease boot missing . . 2 . . (3) Suggest replacement.
Grease boot torn . . 2 . . (4) Suggest replacement.
Grease fitting broken ... A ... Require replacement of grease
fitting.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст