Mitsubishi Montero (1991+). Manual — part 91

AMPLIFIERS

See

RECEIVERS, AMPLIFIERS, EQUALIZERS AND SUB-WOOFER VOLUME CONTROLS .

ANTENNAS

ANTENNA INSPECTION

Condition Code Procedure

Attaching hardware

broken . . . . . A ... Require repair or replacement

of hardware.

Attaching hardware

missing . . . . C . . .. Require replacement of

hardware.

Attaching hardware not

functioning . . . A ... Require repair or replacement

of hardware.

Broken . . . . .. A . . . Require replacement.

Bent . . . . . 2 .. Suggest repair or replacement.

Binding . . . . . 2 .. Suggest repair or replacement.

Connector broken . . A .. Require repair or replacement.

Connector melted . . A . . ... ( 1) Require repair or

replacement.

Connector missing . ... C . . . Require replacement.

Inoperative . . . . A . . (2) Require replacement.

Insulation damaged,

conductors exposed . . A .. Require repair or replacement.

Insulation damaged,

conductors not exposed . 1 . . . Suggest replacement.

Missing . . . . . C . . . Require replacement.

Motor runs continuously . A . . . Require or replacement.

Power antenna noisy . . 2 .. Suggest repair or replacement.

Sticking . . . . 2 .. Suggest repair or replacement.

Terminal broken . . . A .. Require repair or replacement.

Terminal burned, affecting

performance . . . A . . ... ( 1) Require repair or

replacement.

Terminal burned, not

affecting performance .. 2 .. Suggest repair or replacement.

Terminal corroded,

affecting performance .. A .. Require repair or replacement.

Terminal corroded, not

affecting performance .. 2 .. Suggest repair or replacement.

Terminal loose, affecting

performance . . . B .. Require repair or replacement.

Terminal loose, not

affecting performance .. 1 .. Suggest repair or replacement.

(1) - Determine cause and correct prior to repair or

replacement of part.

(2) - Inoperative includes intermittent operation or out of

specification.

BATTERIES

Proper operation of any electrical system or component can be

affected by battery condition. The battery(ies) must meet or exceed

minimum specification for vehicle as equipped and test to that

specific battery’s CCA.

Definition of Terms

* Battery Performance Testing

Testing that determines whether or not a battery meets both

vehicle OEM and battery manufacturer’s specifications.

* Cold Cranking Amp (CCA) Rating

The number of amperes a new, fully charged battery at

0

F (-17.8

C) can deliver for 30 seconds and maintain at

least a voltage of 1.2 volts per cell (7.2 volts for a

12-volt battery).

* Cranking Amps (CA)

The number of amperes a new, fully charged battery, typically

at 32

F (0

C) can deliver for 30 seconds and maintain at

least a voltage of 1.2 volts per cell (7.2 volts for a

12-volt battery).

* OEM Cranking Amps

The minimum CCA required by the original vehicle manufacturer

for a specific vehicle.

BATTERY INSPECTION

Condition Code Procedure

Battery frozen . . .. .. . . . ( 1) Further inspection

required.

Case leaking . . . A . . . Require replacement.

Casing swollen . . .. A . . .. ( 2) Further inspection

required.

Circuit open internally . A . . . Require replacement.

Electrolyte

contamination . . .. A . . ... ( 2) Further inspection

required.

Electrolyte

discoloration . . .. A . . .. ( 2) Further inspection

required.

Fails to accept and hold

charge . . . . . A . . (3) Require replacement.

Fluid level low . . . B . . .. ( 4) Further inspection

required.

Out of performance

specification for

battery . . . . B . . (5) Require replacement.

Out of specification for

application . . . B . . (5) Require replacement.

Post (top or side) burned,

affecting performance .. A . . ... ( 6) Require repair or

replacement.

Post (top or side) burned,

not affecting

performance . . . 2 . . ... ( 6) Suggest repair or

replacement.

Post (top or side)

corroded, affecting

performance . . . A . . . . . Require repair.

Post (top or side)

corroded, not affecting

performance . . . 2 . . . . . Suggest repair.

Post (top or side)

loose . . . . .. A . . . Require replacement.

Post (top or side) melted,

affecting performance .. A . . ... ( 6) Require repair or

replacement.

Post (top or side) melted,

not affecting

performance . . . 2 . . ... ( 6) Suggest repair or

replacement.

Specific gravity low . B . . .. ( 7) Further inspection

required.

State of charge low . . A . . .. ( 7) Further inspection

required.

Top dirty . . . ... 2 . ... Suggest cleaning battery.

Top wet . . . . . A ... (8) Require cleaning battery.

Further inspection required.

Vent cap loose . . .. A ... Require repair or replacement

of vent cap.

Vent cap missing . . C . . .. Require replacement of

vent cap.

(1) - DO NOT attempt to charge a frozen battery. Allow battery

to warm thoroughly and then performance-test. If battery

fails performance test, require replacement.

(2) - No service suggested or required unless the battery fails

performance test, in which case, require replacement.

(3) - This phrase refers to a battery that fails to either

accept and/or retain a charge using appropriate times

listed in the Battery Charging Guide of the BCI Service

Manual, battery charger operating manual, or battery

manufacturer’s specifications.

(4) - Determine cause of low fluid level. Refill to proper

level(s) with water (distilled water preferred). Recharge

battery and performance-test. If battery does not meet

specifications, require replacement. If battery is sealed

type (non-removable filler caps), require replacement.

(5) - The battery may meet battery manufacturer’s specifications

but test below the minimum specification defined by the

vehicle’s OEM for that vehicle.

(6) - Determine cause and correct prior to repair or replacement

of part.

(7) - Recharge and test to manufacturer’s specifications. If

battery fails performance test, require replacement.

(8) - Check fluid level and adjust to manufacturer’s

specification. Suggest checking charging system for

proper operation.

BATTERY CABLES

See BATTERY CABLES, WIRES AND CONNECTORS.

BATTERY CABLES, WIRES AND CONNECTORS

BATTERY CABLE, WIRE AND CONNECTOR INSPECTION

Condition Code Procedure

Application incorrect ... B .. Require repair or replacement.

Attaching hardware

broken . . . . . A ... Require repair or replacement

of hardware.

Attaching hardware

missing . . . . C . . .. Require replacement of

hardware.

Attaching hardware not

functioning . . . A ... Require repair or replacement

of hardware.

Connector broken . . A .. Require repair or replacement.

Connector melted . . A . . ... ( 1) Require repair or

replacement.

Connector missing . ... C . . . Require replacement.

Insulation damaged,

conductors exposed . . A . . ... ( 2) Require repair or

replacement.

Insulation damaged,

conductors not exposed . 1 . . . Suggest replacement.

Open . . . . . A .. Require repair or replacement.

Protective shield

(conduit) melted . ... 2 . . ... ( 1) Suggest repair or

replacement.

Protective shield

(conduit) missing . .. 2 .. Suggest repair or replacement.

Resistance (voltage drop)

out of specification ... A .. Require repair or replacement.

Routed incorrectly . .. B . . . . . Require repair.

Secured incorrectly . . B . . . . . Require repair.

Shorted . . . . . A .. Require repair or replacement.

Terminal broken . . . A .. Require repair or replacement.

Terminal burned, affecting

performance . . . A . . ... ( 1) Require repair or

replacement.

Terminal burned, not

affecting performance .. 2 .. Suggest repair or replacement.

Terminal corroded,

affecting performance .. A .. Require repair or replacement.

Terminal corroded, not

affecting performance .. 2 .. Suggest repair or replacement.

Terminal loose, affecting

performance . . . B .. Require repair or replacement.

Terminal loose, not

affecting performance .. 1 .. Suggest repair or replacement.

Voltage drop out of

specification . . .. A .. Require repair or replacement.

(1) - Determine cause and correct prior to repair or

replacement of part.

(2) - Exposed conductor at replacement (aftermarket) terminal

end does not require repair or replacement.

BATTERY HOLD DOWN HARDWARE

See BATTERY TRAYS AND HOLD DOWN HARDWARE.

BATTERY TRAYS AND HOLD DOWN HARDWARE

BATTERY TRAY AND HOLD DOWN HARDWARE INSPECTION

Condition Code Procedure

Battery improperly

secured . . . . 2 . . . . . Suggest repair.

Bent, affecting

performance . . . A .. Require repair or replacement.

Bent, not affecting