Mitsubishi Montero (1991+). Manual — part 2
released before disconnecting fuel lines.
Removal
1) Release fuel pressure. See FUEL PRESSURE RELEASE under
REMOVAL & INSTALLATION. Remove upper intake manifold. See UPPER INTAKE
MANIFOLD under REMOVAL & INSTALLATION.
2) Drain cooling system. Remove high pressure and return fuel
lines. Cover fuel lines using shop towel during removal as some fuel
may be retained. Remove vacuum hose from pressure regulator.
Disconnect injector harness from injectors.
3) Remove fuel delivery pipe, fuel injectors and pressure
regulator. See Fig. 3. DO NOT allow injectors to fall from delivery
pipe during removal. Remove vacuum hose and pipe assembly.
4) On Montero & Pickup, disconnect coolant temperature
sending unit, coolant temperature switch (A/C equipped), coolant
temperature sensor and thermoswitch (A/T equipped). Disconnect upper
radiator and coolant by-pass hoses. Disconnect heater pipe. On all
models, remove intake manifold and gasket.
Fig. 3: Exploded View of Lower Intake Manifold & Components
Courtesy of Mitsubishi Motor Sales of America, Inc.
Inspection & Installation
1) Inspect for damage and cracks on all mounting surfaces. To
install, reverse removal procedure using new gaskets and "O" rings.
Coat "O" ring with fuel before installation.
2) Install lower intake manifold gasket with adhesive side
toward intake manifold and gasket protrusions facing outboard of
engine. Tighten bolts and nuts to specification. See appropriate
TORQUE SPECIFICATIONS table at end of article. Check for fuel leaks.
TURBOCHARGER
Removal (Front)
1) Drain coolant, and remove radiator. Disconnect exhaust
pipe from turbo. Remove all air intake pipes. Note match marks and
installation depth on air pipes and hoses for reinstallation. Remove
serpentine drive belt. Remove alternator. Remove A/C compressor and
bracket, and support aside.
2) Remove O2 sensor. Remove dipstick assembly and turbo heat
shield. Disconnect turbo coolant feed and return lines. Disconnect
turbo oil feed and return lines. Remove turbocharger assembly.
Removal (Rear)
1) Drain coolant. Remove battery. Disconnect accelerator
cable at bracket and throttle body. Disconnect exhaust pipe from
turbo. Remove all air intake pipes and heat shields. Disconnect
accelerator cable at pedal.
2) Remove clutch booster vacuum hose. Remove O2 sensor.
Remove EGR pipe and turbo heat shield. Disconnect turbo coolant feed
and return lines. Disconnect turbo oil feed and return lines. Remove
turbocharger assembly.
CAUTION: DO NOT allow foreign material into turbocharger air intakes
or coolant and oil passages.
Inspection (Front & Rear)
1) Inspect turbocharger for oil leakage. Check turbine and
compressor wheels for cracks and other damage. Both wheels should turn
easily by hand.
2) Apply 6.8 psi (61 kPa) vacuum to wastegate diaphragm.
Ensure wastegate operates and diaphragm holds vacuum pressure. Use
care when cleaning gasket surfaces so no foreign material enters
turbocharger oil, coolant and air passages.
Installation (Front & Rear)
Refill turbocharger with clean engine oil through oil pipe
installation hole. To complete installation, reverse removal
procedure. Align match marks, and install air pipes and hoses to
proper depth.
EXHAUST MANIFOLDS
Removal (Montero & Pickup)
1) Remove splash shields. Remove O2 sensor. Remove exhaust
pipe-to-manifold nuts. Lower exhaust pipe, and remove gasket. Remove
heat protector. To remove right exhaust manifold, remove air duct,
engine lift bracket and alternator bracket.
2) To remove left exhaust manifold, remove EGR pipe and
gasket. Remove front intake manifold plenum bracket. Remove exhaust
manifolds and gaskets.
Inspection (Montero & Pickup)
Clean all gasket mating surfaces. Inspect for damage and
cracks on all mounting surfaces. Check mounting surfaces of manifold
and cylinder head for warpage. Repair or replace components if warpage
exceeds .012" (.30 mm).
Installation (Montero & Pickup)
To install, reverse removal procedure using new gaskets.
Tighten bolts and nuts to specification. See TORQUE SPECIFICATIONS
(MONTERO & PICKUP) table at end of article.
Removal (3000GT)
1) Remove turbocharger(s) (if equipped). See TURBOCHARGER
under REMOVAL & INSTALLATION. On front manifold, remove serpentine
drive belt and alternator. Remove oil dipstick. On rear manifold,
remove EGR pipe (if equipped).
NOTE: Note locations and direction of installation of exhaust
manifold plain and spring washers for reinstallation
reference. DO NOT mix these fasteners.
2) On all manifolds, remove exhaust pipe-to-manifold nuts.
Lower exhaust pipe, and remove gasket. Remove heat protector. Remove
exhaust manifold nuts and washers. Note locations and direction of
installation of plain and spring washers for reinstallation reference.
DO NOT mix these fasteners. Remove exhaust manifold and gasket.
Inspection (3000GT)
Clean all gasket mating surfaces. Inspect for damage and
cracks on all mounting surfaces. Check mounting surfaces of manifold
and cylinder head for warpage. Repair or replace components if warpage
exceeds .012" (.30 mm).
Installation (3000GT)
To install, reverse removal procedure using new gaskets.
Install new "O" ring on dipstick guide. Coat "O" ring with oil before
installation. Install manifold nuts and washers in original locations.
Tighten nuts to specification in sequence. See Fig. 4. See TORQUE
SPECIFICATIONS (3000GT) table at end of article.
Fig. 4: Exhaust Manifold Tightening Sequence (3000GT)
Courtesy of Mitsubishi Motor Sales of America, Inc.
CYLINDER HEADS
Removal (SOHC)
1) Drain cooling system. Remove upper and lower intake
manifolds and brackets. See UPPER INTAKE MANIFOLD and LOWER INTAKE
MANIFOLD under REMOVAL & INSTALLATION. Remove spark plug wires. Remove
splash shields.
2) Disconnect O2 sensor. Disconnect exhaust pipe from exhaust
manifold, and support to crossmember using wire. Remove heat shields
and exhaust manifolds. See EXHAUST MANIFOLDS under REMOVAL &
INSTALLATION.
3) Remove distributor (left or rear head). Remove timing belt
outer covers, camshaft sprockets, timing belt and timing belt inner
covers. See TIMING BELT under REMOVAL & INSTALLATION. Remove accessory
bracket bolts from front of cylinder head. Remove rocker cover and
gasket.
4) Using Socket (MD998051), loosen cylinder head bolts in 2-3
steps using proper sequence. See Fig. 5. Remove cylinder head and
camshaft assemblies. Note direction of washer installation on head
bolts.
NOTE: Cylinder head bolts must be loosened in 2-3 steps using
proper sequence to prevent cylinder head warpage and
cracking.
Fig. 5: Cylinder Head Bolt Removal & Tightening Sequence
Courtesy of Mitsubishi Motor Sales of America, Inc.
Inspection (SOHC)
Check cylinder head height and warpage at gasket and manifold
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст