Mitsubishi Montero (1991+). Manual — part 290
2) Remove 2 seal plugs. Remove 2 poppet springs and steel
balls. Shift transfer case to "4WD" and pull high-low shift rail out,
in rear cover direction. Remove interlock plunger. Remove pulse
generator (if equipped), front output shaft cover and pulse rotor (if
equipped). Remove snap ring from rear bearing on output shaft. Remove
chain cover, oil guide and side cover. Remove countershaft locking
plate. Remove countershaft.
3) Remove countergear, 2 thrust washers, 2 needle bearings
and spacer through side cover opening. Remove snap ring, spring
retainers and spring from 2WD-4WD shift rail. Remove front output
shaft, rear output shaft and chain as assembly.
4) Remove 2WD-4WD shift fork and distance piece. Drive out
2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug.
Remove high-low shift fork and high-low synchronizer sleeve. Remove
needle bearing and snap ring from input gear. Remove input gear
assembly.
5) If either control shaft or input gear oil seals are to be
replaced, drive out roll pin from transmission control change shifter.
Separate transfer case from adapter. See Fig. 3.
Disassembly (Montero)
1) Remove dynamic damper, 5 detection switches and 3 steel
balls. Remove poppet plug, spring and steel ball. Remove speedometer
gear assembly. Remove output shaft rear cover, spacers, dust seal
guard and oil seals. Front output shaft cover, wave spring and spacer
(if equipped).
2) Remove high-low shift rail plug and high-low shift fork
spring pin. Shift transfer case to "4WD". Remove rear cover and high-
low shift rail. Remove interlock plunger. Remove rear output shaft
(viscous coupling) assembly and center differential assembly. Remove
2WD-4WD synchronizer assembly, chain and front output shaft from
transmission as a unit. With White paint make match marks in grooves
of 2WD-4WD synchronizer in 3 places. With White paint make match marks
on spline projections of 2WD-4WD synchronizer sleeve in 3 places.
Refer to match marks during reassembly.
3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork
and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam
cover and bearing retainer. Remove side cover and gasket. Remove
transfer counter gear shaft, transfer counter gear, thrust washer,
needle bearings and spacer. Remove transfer drive shaft assembly.
Remove high-low shift fork assembly and clutch sleeve. Remove transfer
input gear assembly.
4) Remove 2WD-4WD shift lug spring pin, spring, spring
retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal,
baffle plate, dust seal guard and front output shaft oil seal. See
Fig. 4.
COMPONENT DISASSEMBLY & REASSEMBLY
OUTPUT SHAFT ASSEMBLY (MONTERO)
Disassembly & Reassembly (Rear Shaft)
Remove snap ring and press ball bearing off without putting
pressure on vicious coupling. Remove viscous coupling. To install,
reverse removal procedure. When installing new snap ring, select
thickest ring that will fit into groove. Acceptable clearance is 0-.
003" (0-.08 mm).
Disassembly & Reassembly (Front Shaft)
Remove front bearing. Remove rear bearing. To install reverse
removal procedure.
OUTPUT SHAFT ASSEMBLY (RAM-50)
Disassembly
1) Remove snap ring from rear of output shaft. Remove high-
low synchronizer hub by hand or when low speed gear is pressed off.
Remove bearing spacer and needle bearing. Remove staking from lock nut
on rear output shaft. See Fig. 5. Remove lock nut. Remove ball bearing
from below lock nut. Remove sprocket spacer and steel ball.
2) Remove drive sprocket, 2 needle bearings, sprocket sleeve
and steel ball. Remove 2WD-4WD synchronizer sleeve, hub, stopper plate
and ball bearing.
Reassembly
1) Press ball bearing and stopper plate on front output
shaft, pushing against inner race. After fitting, ensure bearing
rotates smoothly. Install 2WD-4WD synchronizer hub and sleeve. Ensure
hub and sleeve face correct direction. Install steel ball (for
sprocket sleeve positioning) on rear output shaft. Install sprocket
sleeve.
2) Install 2 needle bearings on outer circumference of
sprocket sleeve. Install drive sprocket. Install steel ball and
sprocket spacer. Install ball bearing (press may not be needed as
bearing may be loose). Check for smooth rotation.
3) Tighten sprocket retaining lock nut to specification. See
the TORQUE SPECIFICATIONS table. Stake lock nut with punch. After lock
nut is tightened, ensure drive sprocket rotates smoothly. Install
needle bearing, thrust washer and low speed gear on rear of rear
output shaft.
4) Install needle bearing, thrust washer and low speed gear
on rear output shaft. Mount high-low synchronizer hub. Ensure hub
faces correct direction.
5) Mount high-low synchronizer hub snap ring on front end of
rear output shaft. Selective fit snap rings are available in 5
thicknesses. Use thickest snap ring that will fit into output shaft
groove. Acceptable clearance is 0-.003" (0-.08 mm). See Fig. 5.
Fig. 5: Exploded View Of Output Shaft Assembly (Ram-50)
Courtesy of Mitsubishi Motor Sales of America.
TRANSFER DRIVE SHAFT (MONTERO)
Disassembly & Reassembly
Remove snap ring, high-low synchronizer hub and low speed
gear. Remove bearing spacer, needle bearing and ball bearing. To
assemble, reverse disassembly procedure. Use thickest snap ring that
will fit into output shaft groove. Acceptable clearance is 0-.003" (0-
.08 mm). See Fig. 4.
INPUT SHAFT ASSEMBLY (RAM-50)
Disassembly & Reassembly
1) Remove snap ring from input shaft. Support bearing in
press. Press input shaft out to remove bearing.
2) On manual transmission models, remove spacer and snap ring
from below bearing. Remove cone spring and sub gear. See Fig. 6. For
reassembly, reverse disassembly procedures.
3) Press bearing into input shaft, pushing against inner
race. After fitting, ensure bearing rotates smoothly. Fit snap ring
over front end of input shaft. Snap rings are available in selective
thicknesses. Select thickest snap ring that will fit in groove.
Fig. 6: Exploded View Of Input Shaft Assembly (Ram-50 - Manual
Shown, Automatic Similar)
Courtesy of Mitsubishi Motor Sales of America.
CENTER DIFFERENTIAL CASE (MONTERO)
Disassembly & Reassembly
Separate center differential case front from rear case.
Remove pinion shaft, pinions, thrust washers and dowel pins. Inspect
for excessive wear and replace parts as needed. Align dowel pins and
match marks on outer case circumferences. Assemble front and rear
center differential cases. See the TORQUE SPECIFICATIONS table. Also,
see Fig. 7.
Fig. 7: Exploded View Of Center Differential (Montero)
Courtesy of Mitsubishi Motor Sales of America.
2WD-4WD SYNCHRONIZER (MONTERO)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст