Mitsubishi Galant 9G. Manual — part 1471
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-294
STEP 5. Check the harness wires for short circuit to power
supply between SRS-ECU connector C-122 (terminal No.2
and 1) and seat slide sensor connector D-27 (terminal No.1
and 2).
Q: Are the harness wires between SRS-ECU connector
C-122 (terminal No.2 and 1) and seat slide sensor
connector D-27 (terminal No.1 and 2) in good condition?
YES : Go to Step 6.
NO : Replace the harness wires between SRS-ECU
connector C-122 and seat slide sensor connector
D-27. Then go to Step 6.
STEP 6. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC B1508 set?
YES : Return to Step 1.
NO : The procedure is complete.
AC305362
CONNECTOR: C-122
C-122 (Y)
AI
SRS-ECU
C-122
Harness side
connector
(rear view)
A
B
18
10
15
7
13
5
14
6
16
8
17
9
19
11
20
12
1 2
3 4
AC308165
CONNECTOR : D-27
AC
D-27 (GR)
HARNESS SIDE
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-295
DTC B1509: Improper installation of SRS-ECU
CAUTION
If DTC B1509 is set in the SRS-ECU, always diag-
nose the CAN main bus line.
.
TROUBLE JUDGMENT
This DTC is set when an SRS-ECU, designed only
for the driver's air bag, is installed on the vehicle,
which has both driver's and passenger's air bags.
.
TROUBLESHOOTING HINTS
• Malfunction of the SRS-ECU
.
DIAGNOSIS
Required Special Tool:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A (Vehicles with CAN
communication system)
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
scan tool
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-296
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC B1499 set?
YES : Replace the SRS-ECU (Refer to
).
NO : There is an intermittent malfunction such as poor
engaged connector(s) or open circuit (Refer to
GROUP 00, How to Use Troubleshooting/Inspection
Service Points
− How to Cope with Intermittent
Malfunctions ).
DTC B1519: Connector Lock System Detects Connector Unlocked
CAUTION
If DTC B1519 is set in the SRS-ECU, always diag-
nose the CAN main bus line.
.
DTC SET CONDITIONS
This DTC is set if a poor connection at the SRS-ECU
is detected. However, if the vehicle condition returns
to normal, DTC number B1519 will be automatically
erased, and the SRS warning light will go out.
.
TROUBLESHOOTING HINTS
• Damaged connectors
• Malfunction of the SRS-ECU
.
DIAGNOSIS
Required Special Tool:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A (Vehicles with CAN
communication system)
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-297
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
scan tool
.."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Go to Step 3.
NO : There is an intermittent malfunction such as poor
engaged connector(s) or open circuit (Refer to
GROUP 00, How to Use Troubleshooting/Inspection
Service Points
− How to Cope with Intermittent
Malfunctions ).
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст