Mitsubishi Galant 9G. Manual — part 593
OIL PAN AND OIL PUMP
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-44
INSTALLATION SERVICE POINTS
.
>>A<< LEFT COUNTERBALANCE SHAFT REAR
BEARING INSTALLATION
1. Install special tool MB991603 to the cylinder block.
2. Apply engine oil to the rear bearing outer surface and
bearing hole in the cylinder block.
3. Using special tool MD998705, install the rear bearing.
NOTE: The left rear bearing has no oil holes.
.
>>B<< RIGHT COUNTERBALANCE SHAFT REAR
BEARING INSTALLATION
1. Install the guide pin of the special tool MD998705 in the
threaded hole of the cylinder block as shown.
2. Align the ratchet ball of the special tool MD998705 with the
oil hole in the rear bearing to install the bearing of the
special tool MD998705.
3. Apply engine oil to the bearing outer surface and bearing
hole in the cylinder block.
AK300177
MB991603
MD998705
(STOPPER)
AE
AK300619AE
MB991603
MD998705
(STOPPER)
REAR BEARING
AK300178
MD998705
(GUIDE PIN)
AE
AK300621AC
RATCHET BALL
REAR BEARING RIGHT
OIL HOLE
OIL PAN AND OIL PUMP
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-45
4. Using special tool MD998705, install the rear bearing. Make
sure that the oil hole of the bearing is aligned with the oil
hole of the cylinder block.
.
>>C<< COUNTERBALANCE SHAFT FRONT
BEARING INSTALLATION
1. Remove the rear bearing installing portion from the special
tool MD998705.
2. Install the guide pin of special tool MD998705 in the
threaded hole of the cylinder block as shown.
AK300179
MD998705
(STOPPER)
MD998705
(GUIDE PIN)
AF
AK300622AE
MD998705
(STOPPER)
AK300623AE
REAR BEARING
INSTALLING PORTION
MD998705 (STOPPER)
AK300178
MD998705
(GUIDE PIN)
AE
OIL PAN AND OIL PUMP
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-46
3. Align the ratchet ball of the special tool MD998705 with the
oil hole in the rear bearing to install the bearing of the
special tool MD998705.
4. Apply engine oil to the front bearing outer surface and
bearing hole in the cylinder.
5. Using special tool MD998705, install the rear bearing. Make
sure that the oil hole of the bearing is aligned with the oil
hole of the cylinder block.
.
>>D<< COUNTERBALANCE SHAFT OIL SEAL
INSTALLATION
Using a suitable socket wrench, install the counterbalance shaft
oil seal into the front case.
.
AK300620AC
RATCHET BALL
FRONT BEARING RIGHT
OIL HOLE
AK300179
MD998705
(STOPPER)
MD998705
(GUIDE PIN)
AF
AK300624
AK301071AC
OIL SEAL
SOCKET WRENCH
FRONT CASE
OIL PAN AND OIL PUMP
TSB Revision
ENGINE OVERHAUL <2.4L ENGINE>
11B-47
>>E<< OIL PUMP OIL SEAL INSTALLATION
Using a suitable socket wrench, install the oil pump oil seal into
the front case.
.
>>F<< CRANKSHAFT FRONT OIL SEAL
INSTALLATION
Using special tool MD998375, install the crankshaft front oil
seal into the front case.
.
>>G<< OIL PUMP DRIVEN GEAR/OIL PUMP
DRIVE GEAR INSTALLATION
Install the oil pump gears into the front case and align the align-
ment marks.
.
>>H<< OIL PUMP CASE INSTALLATION
1. Set special tool MD998285 on the front end of crankshaft
and apply a thin coat of engine oil to the outer surface of
special tool MD998285.
2. Apply engine oil to the lip of the crankshaft front oil seal.
AK301070AC
OIL SEAL
SOCKET WRENCH
FRONT CASE
AK301072AC
MD998375
OIL SEAL
FRONT CASE
AK300180
ALIGNMENT
MARK
AC
AK300181AC
MD998285
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст