Mitsubishi Galant 9G. Manual — part 723
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-334
STEP 3. Check harness connector B-36 at cylinder 2, 3
heated oxygen sensor (front) and harness connector B-21,
B-22 at PCM for damage.
Q: Is the harness connector in good condition?
YES : Replace the PCM. Then go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 4.
AK303830
1
2
3
4
AB
CONNECTOR: B-36
B-36 (GR)
CYLINDER 2, 3
HEATED OXYGEN
SENSOR (FRONT)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303052
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTORS: B-21, B-22
AB
B-21 HARNESS CONNECTOR:
COMPONENT SIDE
B-22 HARNESS CONNECTOR:
COMPONENT SIDE
PCM
AIR CLEANER
B-22 (B)
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-335
STEP 4. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 4 −
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0153 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P0154: Cylinder 2, 3 Heated Oxygen Sensor No Activity Detected (sensor 1)
CAUTION
If DTC P0154 has been set, TCL related DTC
U1120 is also set. After P0154 has been diag-
nosed, don't forget to erase DTC U1120.
.
Cylinder 2, 3 Heated Oxygen Sensor
Circuit No Activity Detected (sensor 1)
Circuit
• Refer to DTC P0150 − Cylinder 2, 3 Heated Oxy-
• Refer to DTC P0202 − Injector Circuit-cylinder 2
• Refer to DTC P0203 − Injector Circuit-cylinder 3
.
CIRCUIT OPERATION
• Refer to DTC P0150 − Cylinder 2, 3 Heated Oxy-
• Refer to DTC P0202 − Injector Circuit-cylinder 2
• Refer to DTC P0203 − Injector Circuit-cylinder 3
.
TECHNICAL DESCRIPTION
• The PCM effects air/fuel ratio feedback control in
accordance with the signals from the cylinder 2, 3
heater oxygen sensor (front).
• If the cylinder 2, 3 heated oxygen sensor (front)
has deteriorated, corrections will be made by the
cylinder 2, 3 heated oxygen sensor (rear).
• DTC P0154 becomes stored in memory if a fail-
ure is detected in the above air/fuel ratio feed-
back control system.
.
DESCRIPTIONS OF MONITOR METHODS
Cylinder 2, 3 heated oxygen sensor (front) output
voltage does not cross 0.5 volt within specified
period.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Misfire monitor
Sensor (The sensor below is determined to be
normal)
• Mass airflow sensor
• Engine coolant temperature sensor
• Intake air temperature sensor
• Barometric pressure sensor
• Throttle position sensor
.
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-336
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 20 seconds or more have passed since the
engine starting sequence was completed.
• Engine coolant temperature is higher than 60°C
(140
° F).
• Engine speed is higher than 1,200 r/min.
• Volumetric efficiency is higher than 30 percent.
• Throttle position sensor output voltage is lower
than 4 volts.
• Except while fuel is being shut off.
• Monitoring time: 30 seconds.
Judgment Criteria
• Cylinder 2, 3 heated oxygen sensor (front) output
voltage does not get across 0.5 volt within about
30 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are: )
• Cylinder 2, 3 heated oxygen sensor (front) deteri-
orated.
• Harness damage in cylinder 2, 3 heated oxygen
sensor (front) output line.
• Cylinder 2, 3 heated oxygen sensor (rear) deteri-
orated.
HEATED OXYGEN SENSOR (FRONT)
OUTPUT VOLTAGE CROSSES 0.5V?
START
END
NO
NO
NO
YES
Yes
YES
MALFUNCTION
GOOD
30secs HAVE PASSED?
MONITORING
CONDITIONS
AK203999
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-337
NOTE: When the cylinder 2, 3 heated oxygen
sensor (front) begins to deteriorate, the heated
oxygen sensor output voltage will deviate from
the voltage when the sensor was new (normally
0.5 volt at stoichiometric ratio). This deviation will
be corrected by the cylinder 2, 3 heated oxygen
sensor (rear).
If the cylinder 2, 3 heated oxygen sensor (rear)
responds poorly because it has deteriorated, it
will improperly correct the cylinder 2, 3 heated
oxygen sensor (front). Thus, even when closed
loop control is being effected, the fluctuation of
the cylinder 2, 3 heated oxygen sensor (front)
output voltage decreases, without intersecting
with 0.5 volt. As a result, there is a possibility of
DTC P0154 becoming registered.
• Open circuit in cylinder 2, 3 injector.
• Harness damage in cylinder 2, 3 injector circuit.
• Connector damage.
• PCM failed.
• Exhaust leak.
• Air drawn in from gaps in gasket, seals, etc.
• Incorrect fuel pressure.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
• MB991316: Test Harness
STEP 1. Using scan tool MB991958, check data list item 59:
Cylinder 2, 3 Heated Oxygen Sensor (rear).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
59, Cylinder 2, 3 Heated Oxygen Sensor (rear).
• Warming up the engine. When the engine is revved, the
output voltage should repeat 0 volt and 0.6 to 1.0 volt
alternately.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 2.
NO : Refer to DTC P0156
− Cylinder 2, 3 Heated Oxygen
Sensor Circuit (sensor 2)
, DTC P0157
−
Cylinder 2, 3 Heated Oxygen Sensor Circuit Low
Voltage (sensor 2)
, DTC P0158
− Cylinder
2, 3 Heated Oxygen Sensor Circuit High Voltage
(sensor 2)
, DTC P0159
− Cylinder 2, 3
Heated Oxygen Sensor Circuit Slow Response
(sensor 2)
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст