Mitsubishi Galant 9G. Manual — part 1392
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-4
4. Install a new drain plug gasket so that it faces in the
direction shown in the illustration, and then tighten the drain
plug to the specified torque.
Tightening torque: 39
± 5 N⋅m (29 ± 3 ft-lb)
5. Refill the specified quantity of oil.
Specified Engine Oil: Engine oils displaying ILSAC
certification symbol ("Starburst" symbol) or con-
forming the API classification SL, SL/CF
Total quantity:
<2.4L Engine> 4.3 dm
3
(4.5 quarts)
<3.8L Engine> 4.6 dm
3
(4.9 quarts)
NOTE: SAE 5W-20 and SAE 10W-30 engine oil can be used
in outdoor temperatures ranging from
−
18 to 38
°
C (0 to
100
°
F). However, for optimum fuel economy and cold start-
ing, select the low SAE viscosity grade oil for the expected
temperature range. SAE 5W-20 engine oil is recommended.
6. Install the engine oil filler cap.
7. Check oil level.
ENGINE OIL FILTER REPLACEMENT
M1121001100424
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
− 90°C (176 −
194
°F).
WARNING
Use care as oil could be hot.
2. Remove the engine oil filler cap.
3. Remove the drain plug to drain oil.
AC305936
DRAIN PLUG
GASKET
OIL PAN SIDE
39 ± 5 N·m
29 ± 3 ft-lb
AB
<2.4L ENGINE>
AC305937
DRAIN PLUG
GASKET
OIL PAN SIDE
39 ± 5 N·m
29 ± 3 ft-lb
AB
<3.8L ENGINE>
-20
0
0
20
20
40
40
60
80
100
120
30
10
50
-10
-20
-30
38
-18
F
C
SAE 10W-30
SAE 5W-20 PREFERRED
AC401875 AB
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-5
4. Use an oil filter wrench to remove the engine oil filter.
5. Clean the filter bracket side mounting surface and ensure
the old O-ring has been removed.
6. Apply a small amount of engine oil to the O-ring of the new
oil filter.
7. Screw on the oil filter by hand until it touches the surface of
the flange and then tighten it with an oil filter wrench.
8. Install the drain plug and refill engine oil (Refer to Engine Oil
Replacement
9. Rev the engine a few times, and check to be sure that no
engine oil leaks at the oil filter.
AC000093
MB991610 OR
GENERAL
SERVICE
TOOL
AG
ACX00396
O-RING
AB
NUMBER
ENGINE SPECIAL TOOL
TIGHTENING TORQUE
MD136466,
MD322508
2.4L
General service tool
Approximately 3/4 turn [17
± 3 N⋅m (13 ± 2 ft-lb)]
MD356000
MB991610 or equivalent
Approximately 3/4 turn [14
± 2 N⋅m (124 ± 18 in-lb)]
MD352627,
MD321589
3.8L
General service tool
Approximately one turn [14
± 2 N⋅m (124 ± 18 in-lb)]
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-6
ENGINE OIL PRESSURE CHECK
M1121002300614
Required Special Tool:
MD998054: Engine Oil Pressure Switch Wrench
1. Check engine oil quantity.
CAUTION
Since sealant is applied to the thread of the engine oil
pressure switch, take care not to damage the engine oil
pressure switch when removing it.
2. Use special tool MD998054 to remove the engine oil
pressure switch.
NOTE: Remove the terminal of oil pressure switch where
special tool MD998054 is not fitted.
3. Install the engine oil pressure gauge.
NOTE: Use a 1/8 pipe thread adapter.
4. Run the engine to warm it.
5. After the engine has been warmed up, check that engine oil
pressure is within the standard value.
Standard value:
At idle: 29 kPa (4.2 psi) or more
At 3,500 r/min: 294
− 686 kPa (43 − 100 psi)
6. Remove the engine oil pressure gauge.
7. Apply the specified sealant 3M
AAD Part number 8672 or
equivalent to the threads of the engine oil pressure switch.
AK000197AI
CYLINDER BLOCK
ENGINE OIL
PRESSURE
SWITCH
<2.4L ENGINE>
AK203685
ENGINE OIL
PRESSURE
SWITCH
OIL FILTER
AC
<3.8L ENGINE>
AKX00294
MD998054
AB
AKX00295 AB
SPECIFICATIONS
TSB Revision
ENGINE LUBRICATION
12-7
CAUTION
Do not start the engine within one hour after the engine
engine oil pressure switch has been installed.
8. Use special tool MD998054 to tighten the engine oil
pressure switch to the specified torque.
Tightening torque:
<2.4L ENGINE> 19
± 3 N⋅m (14 ± 2 ft-lb)
<3.8L ENGINE> 10
± 2 N⋅m (87 ± 17 in-lb)
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1121002200305
SERVICE SPECIFICATIONS
M1121000300221
SEALANT
M1121000500225
LUBRICANT
M1121000400701
.
AKX00294
MD998054
AB
ITEM
SPECIFICATION
Engine oil filter
MD352627, MD321589,
MD356000
14
± 2 N⋅m (124 ± 18 in-lb)
MD136466, MD322508
17
± 3 N⋅m (13 ± 2 ft-lb)
Engine oil pan drain plug
39
± 5 N⋅m (29 ± 3 ft-lb)
Engine oil pressure switch
2.4L Engine
19
± 3 N⋅m (14 ± 2 ft-lb)
3.8L Engine
10
± 2 N⋅m (87 ± 17 in-lb)
ITEM
STANDARD VALUE
Engine oil pressure kPa (psi)
at idle
29 (4.2) or more
at 3,500 r/min
294
− 686 (43 − 100)
ITEM
SPECIFIED SEALANT
Engine oil pressure switch
3M
AAD Part No. 8672 or equivalent
ITEM
ENGINE OIL
QUANTITY dm
3
(qt)
Oil filter
Engine oils displaying ILSAC certification
symbol ("Starburst" symbol) or conforming
to the API classification SL, SL/CF
0.3 (0.32)
Total quantity
2.4 L Engine
4.3 (4.5)
3.8 L Engine
4.6 (4.9)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст