Mitsubishi Galant 9G. Manual — part 1565
RADIO WITH CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-132
REMOVAL SERVICE POINT
.
<<A>> ACCESSORY SOCKET REMOVAL
Disengage the claw shown in the illustration and remove the
accessory socket.
RADIO WITH CD PLAYER
GENERAL DESCRIPTION
M1544000100099
<Vehicles without audio amplifier>
• Radio and CD player
• Shows textual information regarding audio
system operation on the low grade type
multi-center display.
<Vehicles with audio amplifier>
• Radio, CD player and CD changer
• Audio amplifier is fitted.
• Shows graphical information regarding audio
system operation on the middle grade type
multi-center display.
RADIO WITH CD PLAYER, SPEAKER AND ANTENNA DIAGNOSIS
INTRODUCTION TO AUDIO SYSTEM DIAGNOSIS
M1544004700101
The diagnosis for symptoms such as noise being
emitted, no sound being played, or sound coming
only out of one speaker (or set of speakers) is pro-
vided.
AUDIO ERROR CODES
If the radio and CD player or radio, CD player and
CD changer detects any malfunction in itself or the
inserted CD, the error codes below will be shown on
the multi-center display.
REMOVAL STEPS
1.
GEARSHIFT LEVER PANEL
2.
ACCESSORY SOCKET (ACC)
3.
ACCESSORY SOCKET COVER
•
FRONT BOX, PLATE, FLOOR
CONSOLE ASSEMBLY (REFER
TO GROUP 52A, FLOOR
CONSOLE ASSEMBLY
.)
4.
INNER BOX (REFER TO GROUP
52A, FLOOR CONSOLE
ASSEMBLY
<<A>>
5.
ACCESSORY SOCKET (+B)
6.
ACCESSORY SOCKET COVER
REMOVAL STEPS (Continued)
AC307190
CLAW
AC
RADIO WITH CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-133
AUDIO SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1544004800379
Use these steps to plan your diagnostic strategy. Fol-
low through with each step to ensure that you have
exhausted all possible methods of finding an audio
system fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Symptom
Chart.
4. Verify that the malfunction is eliminated.
AC208572 AC
LOW GRADE TYPE
MIDDLE GRADE TYPE
ERROR SCREEN SAMPLE (MULTI-CENTER DISPLAY)
ERROR CODES
CAUSE
CAUSE OF TROUBLE AND ITS SOLUTION
LOW
GRADE
TYPE
MIDDLE
GRADE
TYPE
E
ERROR
Connection error
This error code will be shown if the radio and CD
player or radio, CD player and CD changer are not
connected to their related components correctly.
Check the connectors and wiring harness for open or
short circuit.
E01
ERROR
01
Focus error
If there is any problem on the CD, this error code will
be shown. If no error message appears when another
disc is inserted, the disc is defective. Check the items
below, and take a necessary action.
• Contamination, scratch, or deformation
• Formation of moisture or grease
Insert the disc again, and check that no error appear.
E02
ERROR
02
Abnormal disc
E03
ERROR
03
Mechanical error
This error codes will be shown if there is any internal
mechanical or electrical problem in the radio and CD
player or radio, CD player and CD changer. Replace
the radio and CD player or radio, CD player and CD
changer, and check that no error codes are shown.
E HOT
ERROR
HOT
Protection against high
temperature
If the internal temperature is extremely high, this error
code will be shown. Turn off the radio and CD player
or radio, or CD player and CD changer and wait until
they cool down. Wait for a while, and then turn on the
unit again. Check that the same error does not
appear.
RADIO WITH CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-134
TROUBLE SYMPTOM CHART
M1544004900428
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
When power switch is turned "ON," no power is available.
1
Remote controlled radio
switch
When remote controlled radio power
switch is turned "ON," no power is
available. But radio, CD player and CD
changer power switch is available.
<vehicles with audio amplifier>
2
The system does not recognize the
remote controlled radio switch (RH)
only. <vehicles with audio amplifier>
3
The system does not recognize the
remote controlled radio switch (LH) only.
<vehicles with audio amplifier>
4
No sound. <vehicles with audio amplifier>
5
No sound from one speaker. <vehicles without audio amplifier>
6
No sound from one speaker. <vehicles with audio amplifier>
7
Noise
Noise is present while moving (AM).
8
Noise is present while moving (FM).
9
Sound mixed with noise, only at night
(AM).
10
Noise is overpowering both AM and FM. 11
Excessive noise on AM and FM.
12
Noise is detected with engine running.
13
Noise appears during vibration or
shocks.
14
Noise is present wile moving (FM) .
15
Constant noise.
16
Radio
No reception (AM).
17
Poor reception.
18
Distortion on AM and/or FM.
19
Distortion on FM only.
20
Auto select function inoperative, too few
automatic stations are selected.
21
Preset stations are erased.
22
CD player, CD auto
changer
CD can not be inserted.
23
No sound (CD only).
24
CD sound skips.
25
Sound quality is poor.
26
CD cannot be ejected.
27
RADIO WITH CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-135
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: When Power Switch is Turned "ON," no Power is Available.
.
IGNITION
SWITCH (ACC)
RELAY
BOX
RADIO AND CD PLAYER
OR
RADIO, CD PLAYER AND
CD CHANGER
Radio and CD Player or Radio, CD Player and CD Changer Power Supply Circuit
AC305231CH
CONNECTOR: C-29
AC305233BZ
CONNECTOR: C-111
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст