Mitsubishi Galant 9G. Manual — part 370
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-6
GARNISHES AND MOLDINGS
SPECIAL TOOLS
M1511000601158
MOLDINGS
REMOVAL AND INSTALLATION
M1511004700165
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990784 Ornament
remover
General service tool
Side protector molding
Roof drip molding
MB990784
AC306486
AB
2
4
3
1
A
A
A
A
B
B
AB
AC306021
AC306022
AC307267 AB
SECTION A – A
SECTION B – B
3
1, 2
CLIP
DOOR OUTER
PANEL
FRONT FENDER
SIDE OUTER PANEL
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-7
Required Special Tools:
• MB990784: Ornament Remover
ADHESIVE TAPE POSITION
REMOVAL SERVICE POINTS
.
<<A>> SIDE PROTECTOR MOLDING/ROOF DRIP
MOLDING REMOVAL
Gently lift and remove the side protector molding/roof drip
molding. If there is any double-sided tape remaining on the side
protector molding, remove according to the following instruc-
tions.
<Remove double-sided tape remaining on the body surface>
REMOVAL
1. FRONT DOOR SIDE PROTECTOR
MOLDING
2. REAR DOOR SIDE PROTECTOR
MOLDING
ROOF DRIP MOLDING REMOVAL
STEPS
3. ROOF DRIP MOLDING
FRONT DELTA GARNISH REMOVAL
STEPS
4. FRONT DELTA GARNISH
AC306520 AC
ADHESIVE TAPE: DOUBLE-SIDED TAPE
A: 10.0 mm ( 0.39 in ) WIDTH AND 1.52 mm ( 0.06 in ) THICKNESS,
B: 8.0 mm ( 0.32 in ) WIDTH AND 1.2 mm ( 0.05 in ) THICKNESS
FRONT DOOR SIDE PROTECTOR MOLDING
REAR DOOR SIDE PROTECTOR MOLDING
ROOF DRIP MOLDING
B
B
A
36.5 ± 1 mm
(1.44 ± 0.04 inch)
29 ± 1 mm
(1.14 ± 0.04 inch)
5.5 ± 0.5 mm
(0.22 ± 0.02 inch)
6.4 ± 0.5 mm
(0.25 ± 0.02 inch)
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-8
1. Attach protection tape all the way along the edges of the
double-sided tape which is still adhering to the body.
2. Scrape off the double-sided tape with a resin spatula as
much as possible.
3. Peel off the protection tape.
4. Use a shop towel moistened with 3M
AAD Part number
8906 or equivalent to wipe the body.
.
<Remove double-sided tape remaining on SIDE PROTECTOR
MOLDING/ROOF DRIP MOLDING and adhere double-sided
tape (when re-using SIDE PROTECTOR MOLDING/ROOF
DRIP MOLDING)>
1. Scrape off the double-sided tape on the side protector
molding with a resin spatula as much as possible.
2. Use a shop towel moistened with 3M
AAD Part number
8906 or equivalent to wipe the side protector molding
surface.
3. Remove only a small portion of the residual adhesive.
4. Apply primer to adherence area of the side protector
molding, then adhere the double-sided tape as specified on
the side protector molding (Refer to double-sided tape
adherence location ).
INSTALLATION SERVICE POINT
.
>>A<< SIDE PROTECTOR MOLDING/ROOF DRIP
MOLDING INSTALLATION.
1. Tear off the double-sided tape backing paper.
NOTE: If you attach the adhesive tape to the edge of the
backing paper, it will be easy to tear off.
2. Install the side protector molding/roof drip molding.
NOTE: If the double-sided tape is difficult to affix in cold tem-
perature, etc., warm the bonding surfaces of the body and
side protector molding to about 40
−
60
°
C (104
−
140
°
F)
before affixing the tape.
3. Firmly press in the side protector molding.
AC000420
DOUBLE-SIDED TAPE
PROTECTION TAPE
AB
AC000421
DOUBLE-SIDED TAPE
AB
AC000422
AC000657
REAR SPOILER
TSB Revision
EXTERIOR
51-9
REAR SPOILER
REMOVAL AND INSTALLATION
M1511006100147
AC306525
1
2
AB
3
N
REMOVAL STEPS
• TRUNK LID BUMPER (REFER TO
GROUP 42, TRUNK LID
).
1. REAR SPOILER ASSEMBLY
2
HIGH-MOUNTED STOPLIGHT
(REFER TO GROUP 54A,
HIGH-MOUNTED STOPLIGHT
3
PACKING
REMOVAL STEPS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст