Mitsubishi Galant 9G. Manual — part 1597
MULTI-CENTER DISPLAY
TSB Revision
CHASSIS ELECTRICAL
54A-260
STEP 7. Check the multi-center display unit (middle grade
type) power supply circuit [ignition switch (ACC)]. Measure
the voltage at the multi-center display unit (middle grade
type) connector C-05.
(1) Disconnect the multi-center display unit (middle grade type)
connector C-05 and measure at the harness side.
(2) Turn the ignition switch to "ACC" position.
(3) Measure the voltage between terminal 3 and ground by
backprobing.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Go to Step 10.
NO : Go to Step 8.
STEP 8. Check multi-center display unit (middle grade
type) connector C-05 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Is multi-center display unit (middle grade type)
connector C-05 in good condition?
YES : Go to Step 9.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
. The
multi-center display unit (middle grade type) should
work normally.
AC305233
HARNESS SIDE
C-05 (B)
CJ
CONNECTOR: C-05
AC209365
CONNECTOR C-05
(HARNESS SIDE)
HZ
AC305233
HARNESS SIDE
C-05 (B)
CJ
CONNECTOR: C-05
MULTI-CENTER DISPLAY
TSB Revision
CHASSIS ELECTRICAL
54A-261
STEP 9. Check the wiring harness between C-05 (terminal
3) and ignition switch (ACC).
NOTE: Also check joint connector (2) C-03, and intermediate
connector C-29 for loose, corroded, or damaged terminals, or
terminals pushed back in the connector. If or joint connector (2)
C-03 or intermediate connector C-29 is damaged, repair or
replace the wiring harness. Refer to GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between C-05 (terminal 3) and
ignition switch (ACC) in good condition?
YES : There is no action to be taken.
NO : Repair the wiring harness. The multi-center display
unit (middle grade type) should work normally.
AC305233
HARNESS SIDE
C-05 (B)
CJ
CONNECTOR: C-05
AC305232
CONNECTOR: C-03, C-29
C-03
C-29
C-03
C-29
AL
MULTI-CENTER DISPLAY
TSB Revision
CHASSIS ELECTRICAL
54A-262
STEP 10. Check the multi-center display unit (middle grade
type) power supply circuit [ignition switch (IG1)]. Measure
the voltage at the multi-center display unit (middle grade
type) connector C-05.
(1) Disconnect the multi-center display unit (middle grade type)
connector C-05 and measure at the harness side.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 2 and ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Replace the multi-center display unit (middle grade
type). The multi-center display unit (middle grade
type) should work normally.
NO : Go to Step 11.
STEP 11. Check the multi-center display unit (middle grade
type) connector C-05 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Is multi-center display unit (middle grade type)
connector C-05 in good condition?
YES : Go to Step 12.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
. The
multi-center display unit (middle grade type) should
work normally.
AC305233
HARNESS SIDE
C-05 (B)
CJ
CONNECTOR: C-05
AC209365
CONNECTOR C-05
(HARNESS SIDE)
IA
AC305233
HARNESS SIDE
C-05 (B)
CJ
CONNECTOR: C-05
MULTI-CENTER DISPLAY
TSB Revision
CHASSIS ELECTRICAL
54A-263
STEP 12. Check the wiring harness between multi-center
display unit (middle grade type) connector C-05 (terminal
2) and ignition switch (IG1).
NOTE: Also check joint connector (2) C-03, junction block con-
nector C-211 and C-215 for loose, corroded, or damaged termi-
nals, or terminals pushed back in the connector. If joint
connector (2) C-03 or junction block connector C-211 or C-215
is damaged, repair or replace the wiring harness. Refer to
GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between multi-center display unit
(middle grade type) connector C-05 (terminal 2) and
ignition switch (IG1) in good condition?
YES : The procedure is complete.
NO : Repair the wiring harness. The multi-center display
unit (middle grade type) should work normally.
AC305233
HARNESS SIDE
C-05 (B)
CJ
CONNECTOR: C-05
AC305231BP
CONNECTOR: C-03
AC305416
CONNECTORS: C-211, C-215
JUNCTION BLOCK
(FRONT VIEW)
C-215
C-211
HARNESS SIDE
C-211
HARNESS SIDE
C-215
AK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст