Mitsubishi Galant 9G. Manual — part 357

STARTING SYSTEM

TSB Revision

ENGINE ELECTRICAL

16-24

STARTING SYSTEM

GENERAL DESCRIPTION

M1162000100235

If the ignition switch is turned to the "START" posi-
tion, current flows in the coil provided inside mag-
netic switch, attracting the plunger. When the plunger
is attracted, the lever connected to the plunger is
actuated to engage the starter clutch.
On the other hand, attracting the plunger will turn on
the magnetic switch, allowing the "B" terminal and
"M" terminal to conduct. Thus, current flows to
engage the starter motor.

When the ignition switch is returned to the "ON" posi-
tion after starting the engine, the starter clutch is dis-
engaged from the ring gear.
An overrunning clutch is provided between the pinion
and the armature shaft, to prevent damage to the
starter.

OPERATION

When the ignition switch is switched to the "ST" posi-
tion while the selector lever is at the "P" or "N" range,
the contact (magnetic switch) of the starter is
switched ON and the starter motor is activated.

AK202970

PULL-IN COIL

HOLDING
COIL

PLUNGER

LEVER

PINION GEAR

OVERRUNNING
CLUTCH

YOKE

BRUSH

ARMATURE

IGNITION
SWITCH

BATTERY

+

–

AC

B

M

S

STARTING SYSTEM

TSB Revision

ENGINE ELECTRICAL

16-25

STARTING SYSTEM DIAGNOSIS

M1162000700293

TROUBLESHOOTING HINTS

The starter motor does not operate at all.

WARNING

Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.

• Check the starter (coil).

• Check for poor contact at the battery terminals and

starter.

• Check the transmission range switch.

The starter motor doesn't stop

• Check the starter (magnetic switch).

TROUBLESHOOTING GUIDE

The starting system troubleshooting guide is shown in the fol-
lowing steps.

WARNING

Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.

STEP 1.
Q: Is the battery in good condition? (Refer to GROUP 54A,

Chassis Electrical

− Battery − On-vehicle Service −

Battery Check

P.54A-5

.)

YES : Go to Step 2.
NO : Charge or replace the battery.

STEP 2.

• Disconnect the starter motor S (solenoid) terminal connec-

tor.

• Using a jumper wire, apply battery positive voltage to the

starter motor S (solenoid) terminal.

• Check the engine condition.

OK: Turns normally

Q: Dose the starter motor operate normally?

YES :

• Check the ignition switch (Refer to GROUP 54A,

Chassis Electrical

− Ignition Switch − Ignition

Switch

− Inspection

P.54A-48

.)

• Check the transmission range switch. (Refer to

GROUP 23A, Automatic Transaxle

− On-vehicle

Service

− Essential Service − Transmission Range

Switch Check

P.23A-372

.)

• Check the line between the battery and starter

motor S (solenoid) terminal.

NO : Go to Step 3.

STARTING SYSTEM

TSB Revision

ENGINE ELECTRICAL

16-26

STEP 3.

• Check the cable between starter B (battery) terminal and

battery positive terminal for connection and continuity.

Q: Is the starter cable in good condition?

YES : Go to Step 4.
NO : Repair or replace the cable.

STEP 4.

• Check the connection and the continuity of the cable

between the starter motor body and the negative battery
terminal.

Q: Is the ground line in good condition?

YES : Go to Step 5.
NO : Repair or replace the cable.

STEP 5.
Q: Is the starter motor in good condition? (Refer to Starting

System

− Starter Motor Assembly − Inspection

P.16-21

.)

YES : Excessive rotational resistance of the engine.
NO : Replace the starter motor.

STARTER MOTOR ASSEMBLY

REMOVAL AND INSTALLATION <2.4L ENGINE>

M1162001000662

Pre-removal and Post-installation Operation
Air Cleaner Removal and Installation (Refer to GROUP 15,
Air Cleaner

P.15-4

).

AC306713AB

1

5

4

3

2

23 ± 3 N·m
17 ± 2 ft-lb

12 ± 2 N·m
102 ± 22 in-lb

9.0 ± 2.0 N·m
80 ± 17 in-lb

30 ± 3 N·m
23 ± 2 ft-lb

49 ± 9 N·m
36 ± 7 ft-lb

9.0 ± 2.0 N·m
80 ± 17 in-lb

STARTING SYSTEM

TSB Revision

ENGINE ELECTRICAL

16-27

REMOVAL SERVICE POINTS

.

<<A>> ATF WARMER (TRANSMISSION FLUID
COOLER) AND BRACKET ASSEMBLY REMOVAL

With the hose installed, remove the ATF warmer (transmission
fluid cooler) &bracket assembly from the transmission case
front roll stopper bracket.

.

<<B>> STARTER ASSEMBLY REMOVAL

Remove the starter assembly from the side of ATF warmer
(transmission fluid cooler).

REMOVAL STEPS

<<A>>

1.

ATF WARMER (TRANSMISSION
FLUID COOLER) AND BRACKET
ASSEMBLY

2.

STARTER COVER

3.

STARTER CONNECTOR AND
TERMINAL

<<B>>

4.

STARTER ASSEMBLY

5.

STARTER COVER BRACKET

REMOVAL STEPS (Continued)

AC306136

AB

ATF WARMER
(TRANSMISSION
FLUID COOLER)

STARTER ASSEMBLY