Mitsubishi Galant 9G. Manual — part 374
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-22
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
INSPECTION
M1511008300147
WINDSHIELD WASHER MOTOR CHECK
1. Remove the washer tank assembly with the washer hose
attached. Then fill the washer tank with water.
2. Check to see that the water is vigorously sprayed when
connecting the positive battery terminal to terminal number
2 and terminal number 1 to ground.
WINDSHIELD WASHER SWITCH CHECK
4. WINDSHIELD WASHER MOTOR
5. WASHER TANK
WASHER MOTOR REMOVAL STEPS
• FRONT UNDER COVER RH (REFER
TO
• FRONT WASHER HOSE
CONNECTIONS
4. WINDSHIELD WASHER MOTOR
WASHER TANK REMOVAL STEPS
AC307196
2
1
SWITCH POSITION TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
22
− 23
Open circuit
Windshield washer
switch ON
22
− 23
Less than 2 ohms
AC307642
21
22
23
24
25
26
27
28
29
30
31
32
UPPER SIDE
AB
MARK
TSB Revision
EXTERIOR
51-23
MARK
REMOVAL AND INSTALLATION
M1511011800454
AC306546
1
2
3
4
5
AB
A
A
B
C C
B
SECTION B – B
SECTION C – C
SECTION A – A
2
CLIPS
1
3
1. FRONT THREE-DIAMOND MARK
2. REAR THREE-DIAMOND MARK
>>A<<
3. GALANT MARK
>>A<<
4. GRADE MARK
>>A<<
5. 3.8 V6 MARK
MARK
TSB Revision
EXTERIOR
51-24
INSTALLATION SERVICE POINT
.
>>A<< MARK INSTALLATION
1. Installation position
Attach each mark to the position shown in the illustration.
2. Installation procedure
(1) Use 3M
AAD Part number 8906 or equivalent to clean
the mark installation surfaces on the body.
CAUTION
When attaching the marks, the ambient temperature
should be 20
− 38°C (60 − 100°F) and the air should be
completely free of dust. If the ambient temperature is lower
than 20
°C (60°F), the marks and the places on the vehicle
body where the marks are to be attached should be heated
to 20
− 38°C (60 − 100°F).
(2) Peel off the protection sheet on the back of the marks to
affix it in position.
AC305982
REAR BUMPER END LINE
AB
4. GRADE MARK
APPLICATION TAPE
GRADE MARK
AC306556
APPLICATION TAPE
REAR BUMPER END LINE
5. 3.8 V6 MARK
3.8 V6 MARK
GRADE MARK
AB
DOOR MIRROR
TSB Revision
EXTERIOR
51-25
DOOR MIRROR
GENERAL DESCRIPTION
M1511000100570
OPERATION DOOR MIRROR
Remote Controlled Mirror Operation
• The mirror on the door mirror moves up/down
and left/right by operating the remote controlled
door mirror switch when the ignition switch is in
the "ON" or "ACC" position.
Heated Door Mirror operation
• The rear window defogger relay switch is acti-
vated (ON) by turning on the A/C-ECU built-in
rear window defogger switch when the ignition
switch is in the "ON" position. When the rear win-
dow defogger relay is turned ON, power is sup-
plied to the rear window defogger and door
mirror, and the heater of the door mirror (heated
door mirror) starts operations. The rear window
defogger comes with a timer function and will
automatically turn OFF the switch approximately
16 minutes after the rear window defogger switch
is turned ON. The heated door mirror operations
are also terminated along with the rear window
defogger, at this time.
HEATED DOOR MIRROR DIAGNOSIS
TROUBLESHOOTING STRATEGY
M1511014600170
Diagnosis should be carried out by the following pro-
cedures.
1. Gather the information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by the following Symptom
Chart.
4. Verify the malfunction is eliminated.
TROUBLE SYMPTOM CHART
M1511015000171
SYMPTOMS
INSPECTION
PROCEDURE
REFERENCE
PAGE
All heated door mirrors do not operate
1
The right or left heated door mirror does not operate
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст