Mitsubishi Galant 9G. Manual — part 863
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-894
CIRCUIT OPERATION
• A 5-volt power supply is applied on the accelera-
tor pedal position sensor (main) power terminal
(terminal No. 1) from the PCM (terminal No. 30).
The ground terminal (terminal No. 2) is grounded
with PCM (terminal No. 31).
.
TECHNICAL DESCRIPTION
• The accelerator pedal position sensor (main) out-
puts voltage which corresponds to the accelera-
tor pedal depression.
• The PCM checks whether the voltage is within a
specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Accelerator pedal position sensor (main) output volt-
age is out of specified range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
DTC SET CONDITIONS
Logic Flow Chart
.
AK303905
START
END
NO
NO
YES
YES
MALFUNCTION
GOOD
CONTINUOUS
FAILURE FOR 0.3sec
OUTPUT VOLTAGE < 0.6V
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-895
Check Conditions
• Ignition switch is "ON" position.
Judgement Criteria
• Accelerator pedal position sensor (main) output
voltage is 0.6 volt or less for 0.3 second.
.
OBD-II DRIVE CYCLE PATTERN
None.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Accelerator pedal position sensor failed.
• Open or shorted accelerator pedal position sen-
sor (main) circuit, harness damage or connector
damage.
• PCM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using scan tool MB991958, check data list item 78:
Accelerator Pedal Position Sensor (main).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
78, Accelerator Pedal Position Sensor (main).
• Output voltage is between 0.735 and 1.335 volts when
foot is released from accelerator pedal.
• Output voltage is 4.0 volts or higher when accelerator
pedal is fully depressed.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-896
STEP 2. Check harness connector C-24 at accelerator
pedal position sensor for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
STEP 3. Measure the sensor supply voltage at accelerator
pedal position sensor harness side connector C-24.
(1) Disconnect the connector C-24 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 1 and ground.
• Voltage should be between 4.9 and 5.1 volts.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the measured voltage between 4.9 and 5.1 volts?
YES : Go to Step 7.
NO : Go to Step 4.
AK303906
1
6 5 4 3 2
AB
C-24 (B)
CONNECTOR: C-24
HARNESS CONNECTOR:
COMPONENT SIDE
AK303906
1
6 5 4 3 2
AB
C-24 (B)
CONNECTOR: C-24
HARNESS CONNECTOR:
COMPONENT SIDE
1
6 5 4 3 2
AK303203
C-24 HARNESS
CONNECTOR:
COMPONENT SIDE
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-897
STEP 4. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст