Mitsubishi Galant 9G. Manual — part 337
CYLINDER BLOCK HEATER UNIT
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-64
BALANCER TIMING BELT TENSION CHECK
Check the balancer timing belt tension in the following proce-
dures.
1. Apply a pressure of approximately 100 N (22 pounds) at the
center (arrow area) between the sprocket as shown in the
figure, then inspect whether the flexure is within the
standard value.
Standard value: 5
− 10 mm (0.20 − 0.39 inch)
2. If not within the standard value, adjust the belt tension.
(Refer to
CYLINDER BLOCK HEATER UNIT
REMOVAL AND INSTALLATION
M1112006900018
AC301405AB
APPROXIMATELY
100 N (22 lb)
DEFLECTION
Pre-removal Operation
• Front No.1 Exhaust Pipe Removal (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Front No.2 Exhaust Pipe Removal (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Intake Manifold Stay Removal (Refer to GROUP 15,
Post-installation Operation
• Intake Manifold Stay Installation (Refer to GROUP 15,
• Front No.2 Exhaust Pipe Installation (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Front No.1 Exhaust Pipe Installation (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
AC306620
1
2
2.6 ± 0.2 N·m
23 ± 2 in-lb
AB
N
REMOVAL STEPS
1.
CYLINDER BLOCK HEATER UNIT
CONNECTOR
2.
CYLINDER BLOCK HEATER UNIT
CYLINDER BLOCK HEATER UNIT
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-65
REMOVAL SERVICE POINT
.
<<A>> CYLINDER BLOCK HEATER UNIT
REMOVAL
Remove the cylinder block heater unit by using a flat-tipped
screwdriver.
INSTALLATION SERVICE POINT
.
>>A<< CYLINDER BLOCK HEATER UNIT INSTAL-
LATION
1. Install the cylinder block heater unit to the cylinder block
within the range as shown.
2. Tighten the cylinder block heater unit mounting bolt to the
specified torque.
Tightening torque: 2.6
± 0.2 N⋅m (23 ± 2 in-lb)
AC306621
ENGINE FRONT
AB
30˚
A
SECTION A – A
A
30˚
SPECIFICATIONS
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-66
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1111003800354
ITEM
SPECIFICATION
Camshaft and valve stem seal
Accumulator assembly
44
± 5 N⋅m (33 ± 3 ft-lb)
Camshaft position sensing cylinder bolt
22
± 4 N⋅m (16 ± 3 ft-lb)
Camshaft position sensor support bolt
14
± 1 N⋅m (120 ± 13 in-lb)
Camshaft sprocket bolt
89
± 9 N⋅m (65 ± 7 ft-lb)
Connector bracket bolt
11
± 1 N⋅m (98 ± 8 in-lb)
Control wiring harness bolt
9.0
± 2.0 N⋅m (80 ± 17 in-lb)
Control wiring harness protector bolt
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Cylinder head plug
47
± 7 N⋅m (35 ± 5 ft-lb)
Engine oil control valve bolt
11
± 1 N⋅m (98 ± 8 in-lb)
Engine oil pressure switch
10
± 2 N⋅m (89 ± 17 in-lb)
Exhaust rocker arm shaft bolt
13
± 1 N⋅m (115 ± 9 in-lb)
Intake rocker arm shaft bolt
31
± 3 N⋅m (23 ± 2 ft-lb)
Rocker cover assembly bolt
3.5
± 0.5 N⋅m (31 ± 4 in-lb)
Spark plug
25
± 4 N⋅m (18 ± 3 ft-lb)
Crankshaft oil seal
A/T drive plate bolt
132
± 5 N⋅m (98 ± 3 ft-lb)
Crankshaft pulley
Crankshaft damper pulley bolt
25
± 4 N⋅m (18 ± 3 ft-lb)
Cylinder block heater unit
Cylinder block heater unit bolt
2.6
± 0.2 N⋅m (23 ± 2 in-lb)
Cylinder head gasket
Camshaft sprocket bolt
89
± 9 N⋅m (65 ± 7 ft-lb)
Control wiring harness bolt
9.0
± 2.0 N⋅m (80 ± 17 in-lb)
Control wiring harness protector bolt
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Cylinder head bolt <Cold engine>
78
± 2 N⋅m → 0 N⋅m → 20 ± 2 N⋅m →
+90
° → +90° (58 ± 1 ft-lb → 0 in-lb →
15
± 1 ft-lb → +90° → +90°)
Engine oil dipstick guide bolt
13
± 1 N⋅m (115 ± 9 in-lb)
Generator terminal nut
12
± 2 N⋅m (102 ± 22 in-lb)
Intake manifold stay bolt
31
± 3 N⋅m (23 ± 2 ft-lb)
Knock sensor connector bracket bolt
11
± 1 N⋅m (98 ± 8 in-lb)
Pressure hose clamp bolt
12
± 2 N⋅m (102 ± 22 in-lb)
Radiator lower hose clamp bolt
11
± 1 N⋅m (98 ± 8 in-lb)
Water hose clamp bolt
11
± 1 N⋅m (98 ± 8 in-lb)
SPECIFICATIONS
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-67
Engine assembly
ATF warmer (transmission fluid cooler) bracket bolt
23
± 3 N⋅m (17 ± 2 ft-lb)
Battery terminal nut
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Control wiring harness bolt and nut
9.0
± 2.0 N⋅m (80 ± 17 in-lb)
Control wiring harness protector bolt
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Engine front mounting bracket bolt
M10
58
± 7 N⋅m (43 ± 5 ft-lb)
Engine front mounting bracket bolt and nut
M12
83
± 12 N⋅m (61 ± 9 ft-lb)
Grounding cable bolt
9.0
± 2.0 N⋅m (80 ± 17 in-lb)
Power steering oil pump bracket bolt
24
± 4 N⋅m (18 ± 3 ft-lb)
Power steering oil pump bracket nut
44
± 10 N⋅m (33 ± 7 ft-lb)
Pressure hose clamp bolt
12
± 2 N⋅m (102 ± 22 in-lb)
Oil pan
Baffle plate bolt (bolt, washer assembled)
M6
9.0
± 2.0 N⋅m (80 ± 17 in-lb)
M8
22
± 4 N⋅m (16 ± 3 ft-lb)
Engine oil pan bolt
9.0
± 3.0 N⋅m (80 ± 26 in-lb)
Engine oil pan drain plug
39
± 5 N⋅m (29 ± 3 ft-lb)
Engine oil pan strainer bolt
19
± 3 N⋅m (14 ± 2 ft-lb)
Torque converter housing front lower cover bolt (bolt, flange) M10
26
± 5 N⋅m (19 ± 4 ft-lb)
Torque converter housing front lower cover bolt (bolt, washer
assembled)
M6
9.0
± 1.0 N⋅m (80 ± 9 in-lb)
Timing belt
Auto-tensioner bolt (bolt, washer assembled)
M8
22
± 4 N⋅m (16 ± 3 ft-lb)
M10
44
± 10 N⋅m (33 ± 7 ft-lb)
Balancer timing belt tensioner bolt
19
± 3 N⋅m (14 ± 2 ft-lb)
Connector bracket bolt
11
± 1 N⋅m (98 ± 8 in-lb)
Crankshaft pulley center bolt
167 N
⋅m (123 ft-lb)
Cylinder block plug
30
± 3 N⋅m (23 ± 2 ft-lb)
Generator terminal nut
12
± 2 N⋅m (102 ± 22 in-lb)
Idler pulley bolt
79
± 5 N⋅m (59 ± 3 ft-lb)
Timing belt idler pulley bolt
35
± 6 N⋅m (26 ± 4 ft-lb)
Timing belt lower cover bolt (bolt, flange)
M6
11
± 1 N⋅m (98 ± 8 in-lb)
Timing belt lower cover bolt (bolt, washer assembled)
M6
9.0
± 1.0 N⋅m (80 ± 9 in-lb)
Timing belt lower cover bracket bolt
8.5
± 0.5 N⋅m (76 ± 4 in-lb)
Timing belt lower cover nut
11
± 1 N⋅m (98 ± 8 in-lb)
Timing belt tensioner adjuster bolt
23
± 3 N⋅m (17 ± 2 ft-lb)
Timing belt tensioner arm bolt
21
± 4 N⋅m (16 ± 2 ft-lb)
Timing belt tensioner pulley bolt
48
± 5 N⋅m (36 ± 3 ft-lb)
Timing belt upper cover bolt (bolt, flange)
M6
11
± 1 N⋅m (98 ± 8 in-lb)
M8
14
± 1 N⋅m (120 ± 13 in-lb)
Water pump pulley bolt
8.8
± 1.0 N⋅m (78 ± 9 in-lb)
ITEM
SPECIFICATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст