Mitsubishi Galant 9G. Manual — part 1604
NOTES
35B-1
GROUP 35B
ANTI-LOCK
BRAKING SYSTEM
(ABS)
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
ANTI-LOCK BRAKING SYSTEM (ABS)
DIAGNOSIS . . . . . . . . . . . . . . . . . . . .
INTRODUCTION TO ANTI-LOCK BRAKING
SYSTEM DIAGNOSIS . . . . . . . . . . . . . . . .
ABS DIAGNOSTIC TROUBLESHOOTING
STRATEGY. . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSTIC FUNCTION . . . . . . . . . . . . .
DIAGNOSTIC TROUBLE CODE CHART. .
DIAGNOSTIC TROUBLE CODE
PROCEDURES. . . . . . . . . . . . . . . . . . . . . .
SYMPTOM CHART. . . . . . . . . . . . . . . . . . .
SYMPTOM PROCEDURES . . . . . . . . . . . .
DATA LIST REFERENCE TABLE . . . . . . .
ACTUATOR TEST REFERENCE TABLE. .
CHECK AT ABS-ECU. . . . . . . . . . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE . . . . . . . . . . .
WHEEL SPEED SENSOR OUTPUT
VOLTAGE MEASUREMENT. . . . . . . . . . . .
HYDRAULIC UNIT CHECK . . . . . . . . . . . . .
IN THE EVENT OF A DISCHARGED
BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . .
HYDRAULIC UNIT . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
WHEEL SPEED SENSOR . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
FASTENER TIGHTENING
SPECIFICATION . . . . . . . . . . . . . . . . . . . . .
GENERAL SPECIFICATIONS . . . . . . . . . .
SERVICE SPECIFICATION . . . . . . . . . . . .
GENERAL DESCRIPTION
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-2
GENERAL DESCRIPTION
M1352000100454
FEATURES
The 4ABS ensures directional stability and control
during hard braking.
This ABS uses a 4-sensor 4-channel system that
controls all four wheels independently of each other.
The basic system is the same as that for the Lancer.
• EBD (Electronic Brake-force Distribution system)
control provides the ideal braking force for the
rear wheels.
• To shorten the harness wires and enhance data
transmission reliability, communication with other
ECU is performed over a CAN (Controller Area
Network).
NOTE: For further details on CAN communica-
tion, refer to GROUP 54C, CAN.
• Fail-safe function ensures that safety is main-
tained.
• Diagnostic function provides improved service-
ability.
EBD CONTROL
In ABS, electronic control is used so the rear wheel
brake hydraulic pressure during braking is regulated
by rear wheel control solenoid valves in accordance
with the vehicle's rate of deceleration. The front and
rear wheel slippage are calculated from the signals
received from the various wheel sensors. EBD con-
trol provides a high level of control for both vehicle
braking force and vehicle stability. The system has
the following features:
• Because the system provides the optimum rear
wheel braking force regardless of vehicle load
and the condition of the road surface, the system
reduces the required pedal depression force, par-
ticularly when the vehicle is heavily loaded.
• Because the duty placed on the front brakes is
reduced, the increases in pad temperature can
be controlled during front brake application to
improve pad wear.
• Control valves such as the proportioning valve
are not required.
GENERAL DESCRIPTION
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-3
CONSTRUCTION DIAGRAM
AC306051
AB
1
1
3, 7
5
2
4
1
1
6
5
4
VEHICLES FOR CANADA
VEHICLES FOR USA
NAME OF PART
NUMBER
OUTLINE OF FUNCTION
Sensor
Wheel speed sensor
1
Sends alternating current signals at frequencies which are
proportional to the rotation speeds of each wheel to the
ABS-ECU.
Stoplight switch
2
Sends a signal to the ABS-ECU to indicate whether the
brake pedal is depressed or not.
Actuator Hydraulic unit
3
Drives the solenoid valves according to signals from the
ABS-ECU in order to control the brake hydraulic pressure
for each wheel.
ABS warning light
4
Illuminates in response to signals from the ABS-ECU
when a problem develops in the ABS system.
Brake warning light
5
Illuminates in response to signals from the ABS-ECU
when a problem develops in the EBD system.
Data link connector
6
Outputs the diagnostic trouble codes and allows
communication with the scan tool.
ABS-ECU
7
Controls actuators (described above) based on the signals
coming from each sensor.
Controls the self-diagnosis and fail-safe functions.
Controls the diagnostic function (scan tool compatible).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст