Mitsubishi Galant 9G. Manual — part 1531
WHEEL AND TIRE DIAGNOSIS
TSB Revision
WHEEL AND TIRE
31-6
WHEEL BALANCER CALIBRATION CHECKING FLOW CHART
AC000040
Balance wheel.
Rotate wheel 1/2 turn.
Imbalance = 5 g (0.18 oz) or less
Imbalance = more than 5 g (0.18 oz)
Rebalance wheel.
Rotate wheel 1/4 turn.
Imbalance = 5 g (0.18 oz) or less
Imbalance = more than 5 g (0.18 oz)
Verify wheel is properly centered.
Verify cones, cup, and wing nut are clean,
undamaged, and appropriate for wheel.
Make necessary corrections, then recheck
wheel balance.
Attach a 5-g (0.18-oz) weight to the outer rim.
Is the imbalance 5 ± 2 g (0.18 ± 0.06 oz) at 170
–
190 degrees away from the 5-g (0.18-oz) weight?
YES
NO
Attach a 5-g (0.18-oz) weight to the inner rim at 180
degrees opposite the weight on the outer rim.
Is the imbalance 5 ± 2 g (0.18 ± 0.06 oz) at 170
–
190 degrees away from both 5-g (0.18-oz) weights?
YES
NO
Balancer does not require
calibration.
Balancer requires calibration.
Contact balancer manufacturer.
ZERO CALIBRATION
CHECK
STATIC BALANCE
CHECK
DYNAMIC BALANCE
CHECK
AD
ON-VEHICLE SERVICE
TSB Revision
WHEEL AND TIRE
31-7
ON-VEHICLE SERVICE
TIRE INFLATION PRESSURE CHECK
M1311000900323
NOTE: For information on tire inflation pressure, refer to the
label attached to the center pillar on the driver's side.
TIRE WEAR CHECK
M1311001000345
Measure the tread depth of the tires.
Minimum limit: 1.6 mm (0.06 inch)
If the remaining tread depth is less than the minimum limit,
replace the tire.
NOTE: When the tread depth of the tires is reduced to 1.6 mm
(0.06 inch) or less, wear indicators will appear.
WHEEL RUNOUT CHECK
M1311001100364
Jack up the vehicle so that the wheels are clear of the floor.
While slowly turning the wheel, measure wheel runout with a
dial indicator.
Limit:
If wheel runout exceeds the limit, replace the wheel.
WHEEL AND TIRE
INSTALLATION SERVICE POINT
M1311001300302
Tighten the wheel nuts to the specified torque.
Tightening torque: 98
± 10 N⋅m (73 ± 7 ft-lb)
ITEM
STEEL WHEEL
ALUMINUM
WHEEL
Radial runout 1.2 mm (0.05 inch)
or less
1.0 mm (0.04 inch)
or less
Lateral
runout
1.2 mm (0.05 inch)
or less
1.0 mm (0.04 inch)
or less
ACX00651AB
LATERAL
RADIAL
SPECIFICATIONS
TSB Revision
WHEEL AND TIRE
31-8
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATION
M1311001600295
GENERAL SPECIFICATIONS
M1311000200324
.
<2.4L ENGINE>
NOTE:
.
•
The * mark indicates optional item.
•
PCD (Pitch Circle Diameter) indicates the pitch circle diameter of the wheel installation holes.
.
ITEM
SPECIFICATION
Wheel nut
98
± 10 N⋅m (73 ± 7 ft-lb)
ITEM
DE MODEL
ES MODEL
SRHYL4M
SRHYSL9M
SRHYL5M
SRPYL4M
SRPYSL9M
SRPYL5M
SRXYL4M
SRXYSL9M
SRXYL5M
Wheel
Type
Steel type
Steel type or
Aluminum type*
Aluminum type
Size
16
× 6 1/2JJ
Amount of wheel
offset mm (in)
46 (1.8)
Pitch circle diameter
(PCD) mm (in)
114.3 (4.50)
Tire
Size
P215/60 R16 94H
Spare wheel
Type
Steel type
Size
16
× 4T
Amount of wheel
offset mm (in)
40 (1.5)
Pitch circle diameter
(PCD) mm (in)
114.3 (4.50)
Spare tire
Size
T125/70 D16
SPECIFICATIONS
TSB Revision
WHEEL AND TIRE
31-9
<3.8L ENGINE>
NOTE:
.
•
The * mark indicates optional item.
•
PCD (Pitch Circle Diameter) indicates the pitch circle diameter of the wheel installation holes.
SERVICE SPECIFICATIONS
M1311000300406
ITEM
LS MODEL
GTS MODEL
SRHEL4M
SRHEL5M
SRPEL4M
SRGEL5M
SRGEL4M
Wheel
Type
Steel type or
Aluminum type*
Aluminum type
Aluminum type
Size
16
× 6 1/2JJ
17
× 7JJ
Amount of wheel
offset mm (in)
46 (1.8)
Pitch circle diameter
(PCD) mm (in)
114.3 (4.50)
Tire
Size
P215/60 R16 94H
P215/55 R17 93V
Spare wheel
Type
Steel type
Size
16
× 4T
Amount of wheel
offset mm (in)
40 (1.5)
Pitch circle diameter
(PCD) mm (in)
114.3 (4.50)
Spare tire
Size
T125/70 D16
ITEM
LIMIT
Tread depth of tire mm (in)
Minimum 1.6 (0.06)
Wheel runout
<Aluminum wheel>
Radial runout mm (in)
1.0 (0.04) or less
Lateral runout mm (in)
1.0 (0.04) or less
Wheel runout
<Steel wheel>
Radial runout mm (in)
1.2 (0.05) or less
Lateral runout mm (in)
1.2 (0.05) or less
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст